Compaq 740 Manual do usuário

C

OMPAQ

MV740 C

OLOR

M

ONITOR

U

SER

’

S

G

UIDE

G

UIA DO

U

SUÁRIO DO

M

ONITOR

C

OLORIDO

C

OMPAQ

MV740

M

ANUEL DE L

’

UTILISATEUR

DU MONITEUR COULEUR

MV740 C

OMPAQ

G

UÍA DE

U

SUARIO DEL

M

ONITOR

EN

C

OLOR

MV740

DE

C

OMPAQ

The information in this guide is subject to change without notice.

COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL

OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN; NOR FOR

INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE

FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.

This guide contains information protected by copyright. No part of this guide may be photocopied or

reproduced in any form without prior written consent from Compaq Computer Corporation.

 2000 Compaq Computer Corporation. Printed in Brazil, Canada, China, Japan, Korea, Malaysia,

Mexico, Singapore, Taiwan, Thailand, the United Kingdom, and the United States.

Compaq is registered in the U.S. Patent and Trademark Office.

Microsoft, MS-DOS, and Windows are registered trademarks of Microsoft Corporation.

The software described in this guide is furnished under a license agreement or nondisclosure agreement.

The software may be used or copied only in accordance with the terms of the agreement.

Product names mentioned herein may be trademarks and/or registered trademarks

of their respective companies.

153728-001

1

T

ABLE OF

C

ONTENTS

INTRODUCTION...........................................................................................................................2

Features............................................................................................................................................................2

GETTING STARTED......................................................................................................................3

Installation........................................................................................................................................................ 4

Speaker Installation................................................................................................................................... 5

OPERATING YOUR MONITOR.......................................................................................................6

Using Your On-Screen Display...........................................................................................................................7

No Signal Message............................................................................................................................................8

Out of Range Message......................................................................................................................................8

On-Screen Display Functions.....................................................................................................................9

ENERGY SAVER MODES............................................................................................................10

MONITOR CARE AND MAINTENANCE.........................................................................................11

TROUBLESHOOTING..................................................................................................................12

SHIPPING YOUR MONITOR.........................................................................................................14

SPECIFICATIONS.......................................................................................................................15

APPENDIX.................................................................................................................................16

Regulatory Compliance Notices....................................................................................................................... 16

Federal Communications Commission Notice...........................................................................................16

Modifications........................................................................................................................................... 16

Cables..................................................................................................................................................... 16

Declaration of Conformity for products marked with the FCC logo - United States only .............................16

Canadian Notice....................................................................................................................................... 17

Avis Canadien..........................................................................................................................................17

European Union Notice............................................................................................................................. 17

EPA Energy Star Compliance.................................................................................................................... 17

Japanese Notice......................................................................................................................................17

German Ergonomics Notice......................................................................................................................17

2

I

NTRODUCTION

Congratulations on the purchase of your new, easy-to-use Compaq MV740 Color Monitor. The MV740

is a state-of-the-art, high performance monitor featuring a 17-inch (15.9-inch/405.2 mm viewable

image area) screen. The On-Screen Display allows you to make quick and easy adjustments to your

screen image.

Features

• 17-inch monitor with a large, 15.9-inch/405.2 mm viewable screen to comfortably view

multiple applications and large documents

• .28mm dot pitch to produce crisp, sharp images

• On-screen user controls for easy adjustment of the screen image

• Quick, easy setup

• Energy Star compliant for reduced power consumption

• Integrated microphone for all of your Internet, telephony, and multimedia applications

• Attachable or standalone JBL Platinum Series amplified speakers

− Integrated audio input jack for MP3 players and other portable audio devices

− Integrated headphone jack

3

G

ETTING

S

TARTED

WARNING:

It is strongly recommended that TWO people remove the monitor from its box. This

will help ensure that the monitor is not dropped. Dropping the monitor could cause personal

injury or could damage the monitor.

Your Compaq MV740 Color Monitor packaging should include the following:

• Monitor

• Power cord

• Microphone cable

• Speakers and speaker power cable or adapter (selected models)

• Speaker stands

• User documentation

• Setup poster

CAUTION:

Do not place your monitor

face down. Damage could result to the

front panel controls or to your monitor

screen.

4

Installation

Before installing your monitor, place it in a convenient, well-ventilated location near your computer,

ensure that power to your computer and other peripheral devices is turned off, and proceed as follows:

1. Insert the speaker power cable 1 into the back of the right speaker

. Insert the plug from the left

speaker into the socket on the back of the right speaker

.

2. Insert the other end of the speaker power cable 3

c

cc

c

into the back of the monitor

.

3. Connect the lime green plug from the right speaker 2 to the audio out

socket on the back of

your computer.

4. Connect the pink end of the microphone cable to the microphone socket

on the back panel of

your monitor 3

b

bb

b

, then plug the other end of the cable into the microphone connector on the rear

panel of your computer 6.

5. Connect the monitor signal cable from the back of the monitor to the blue socket on the back of the

computer 4. Tighten the screws on the end of the connector.

IMPORTANT:

Ensure that the signal cable aligns with the 15-pin connector. Do not force the cable onto

the connector or you may damage the signal cable.

(

Installation instructions continued on next page

.)

5

6. Connect the power cord to the back of the monitor 3

a

aa

a

, then connect the power cord to a power

outlet 5.

WARNING:

To reduce the risk of electric shock or damage to your equipment, do not disable

the power cord grounding feature. This equipment is designed to be connected to a grounded

(earthed) power outlet that is easily accessible to the operator. The grounding plug is an

important safety feature.

WARNING:

For your safety, be sure that the power outlet you plug your power cord into is

easily accessible and located as close to the equipment operator as possible. When you need

to disconnect power to the equipment, unplug the power cord from the power outlet by

grasping the plug firmly. Never pull on the cord.

CAUTION:

For the protection of your monitor as well as your computer, connect all power

cords for your computer and its peripheral devices (monitor, printer, scanner, and so on) to

some form of surge protection such as a power strip or UPS (Uninterruptible Power Supply).

Not all power strips provide surge protection; they must be specifically labeled as having this

ability. Look for manufacturers that have a Damage Replacement Policy to replace your

equipment if their surge protection fails.

7. Install your speakers using one of the methods listed in “Speaker Installation.”

8. Power on your monitor by pressing the power button 7. Power on the speakers by pressing the

power button on the side of the right speaker.

If necessary, adjust the front panel controls according to your personal preference.

Your monitor installation is now complete.

Speaker Installation

Headphone/Audio Input Jacks Retractable Speaker Mechanism Speaker Stand

Insert the headphone connector

(headphones not included) into the

headphone jack.

Insert one end of the cable from

your portable audio device (not

included) into the speaker.

1.

Rotate the thumbwheel up to extend

the hook mechanism.

2.

Align the hooks with the slots on the

monitor, then gently insert the hooks

into the slots and slide down to lock in

place.

Insert the speaker stand into the slot on

the rear of each speaker.

6

O

PERATING

Y

OUR

M

ONITOR

Front Panel Controls

Control Function

1

Select button

Backward button (left arrow) moves backward through menu

options or

decreases

adjustment levels.

2

Select button

•

Launches On-Screen Display

•

Selects functions and adjustments

•

Exits menus and On-Screen Display

3

Forward button

Forward button (right arrow) moves forward through menu

options or

increases

adjustment levels.

4

Power LED

•

Green light—indicates power on

•

Yellow light—indicates Standby/Suspend mode

•

Amber light—indicates Sleep mode

For more information on power states, see "Energy Saving

Modes."

5

Power button

Turns the monitor on and off.

7

Using Your On-Screen Display

The On-Screen Display (OSD) adjusts the screen image based on your viewing preferences. To access

the On-Screen Display, do the following:

1. If your monitor is not already on, press the power button to turn it on. (For the location of front

panel control buttons, see “Front Panel Controls” in the previous section).

2. Press the

Select

SelectSelect

Select

button

to display the On-Screen Display menu.

3. To select a function, press the

Forward

ForwardForward

Forward

or

Backward

BackwardBackward

Backward

button until the function is

highlighted.

4. Press

to choose the function.

5. An adjustment window is displayed. Use the

Forward

ForwardForward

Forward

and

Backward

BackwardBackward

Backward

button to increase

(Forward) or decrease (Backward) the level of adjustment.

6. Press

to save the new adjustment.

7. To exit the On-Screen Display, select the

Exit

ExitExit

Exit

icon, then press the

Select

SelectSelect

Select

button

once.

8

No Signal Message

If a “NO SIGNAL” message displays on your monitor, check to be sure your VGA cable is properly

connected, and ensure that your computer is powered on.

Out of Frequency Range Message

If an “OUT OF Frequency RANGE” message appears on your screen, your video resolution and/or

refresh rate are set higher than what your monitor supports. To correct this problem, follow the steps

below or contact your Compaq authorized dealer, reseller, or service provider.

1. Restart your computer.

2. Press

F6

F6F6

F6

before Microsoft® Windows® begins to load so that you can enter Safe Mode.

3. Change your display settings to a supported setting (see “Specifications”).

4. Restart your computer so that the new settings take effect.

9

On-Screen Display Functions

Your On-Screen Display (OSD) menu accesses the following functions:

On-Screen Display Functions

On-Screen Display Function

Contrast

Adjusts display contrast

Brightness Adjusts display brightness

H. Position Shifts display right or left

H. Size Increases and decreases display width

V. Position Shifts display up or down

V. Size Increases and decreases display height

Pincushion Adjusts the concave and convex portion of the picture

Trapezoid Adjusts the top and bottom display widths to make them even

Pin. Balance Adjusts each side of Pincushion

Parallelogram Adjusts the tilt of the display sides to the left or right

Rotation Adjusts the tilt of the display

Degauss Demagnetizes screen to reduce color impurities

Color Temp Adjusts picture for more vibrant colors

Reset Resets monitor to factory default values

Exit Exits OSD menu

10

E

NERGY

S

AVER

M

ODES

Your monitor is designed to meet strict EPA (Environmental Protection Agency) Energy Star

requirements for reduced power consumption and to comply with the VESA Standard Display Power

Management Signal. Using a combination of hardware and software functions, this energy-saving

feature allows your computer to control your monitor’s power consumption and reduce your monitor’s

power state when not in use.

NOTE:

Power consumption does not include the speaker power.

IMPORTANT:

Your monitor’s energy saver feature works only when your monitor is connected to a computer

that also has energy saver features.

The following table describes your monitor energy saver levels in each of four power states:

Power Management States

State LED color Power

Consumption

Description

ON

Green <100 watts Normal operation

STANDBY/

SUSPEND

Yellow <15 watts Monitor screen is blank. High voltage is off. Heater

voltage is reduced. Full power mode returns quickly

(approximately 4 seconds).

SLEEP

Amber <5 watts Monitor screen is blank. High voltage is off. Heater

voltage is off. There is a brief warm-up period before

returning to full power mode (approximately 15

seconds).

The energy saver utility, with its energy saver features, is available with the Microsoft® Windows®

operating system, and some features are available in DOS. Refer to your computer’s user guide for

instructions on setting energy saver features (also referred to as power management features).

11

M

ONITOR

C

ARE AND

M

AINTENANCE

To enhance the performance and extend the life of your monitor, use the following guidelines:

• Do not open your monitor cabinet or attempt to service this product yourself. Adjust only

those controls that are covered in the operating instructions. If your monitor is not

operating properly or has been dropped or damaged, contact your Compaq authorized

dealer, reseller, or service provider.

• Place your monitor at least 3 inches (76 mm) away from walls or other enclosures.

• Use only a power source and connection appropriate for this monitor, as indicated on the

label/back plate.

• When you connect your monitor to an outlet or extension cord, be sure the total ampere

rating of the products connected to the outlet does not exceed the current rating of the

electrical outlet, and the total ampere rating of the products connected to the cord does not

exceed the rating of the cord.

• Install your monitor near an outlet that you can easily reach. Disconnect your monitor by

grasping the plug firmly and pulling it from the outlet. Never disconnect your monitor by

pulling the cord.

• Turn your monitor off when not in use. You can substantially increase the life expectancy

of your monitor by using a screen saver program and turning off your monitor when not in

use.

• Unplug your monitor from the wall outlet before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning. If the screen requires additional cleaning,

use an antistatic CRT screen cleaner.

CAUTION:

Do not use benzene, thinner, ammonia, or any other volatile

substances to clean your monitor or the screen. These chemicals may damage

the cabinet finish as well as the screen.

• Slots and openings in the cabinet are provided for ventilation. These openings must not be

blocked or covered. Never push objects of any kind into cabinet slots or other openings.

• Do not place plants on top of your monitor. Water or dirt from the plant may get into

the vents.

• Do not drop your monitor or place it on an unstable surface.

• Do not allow anything to rest on the power cord. Do not walk on the cord.

• Keep your monitor in a well-ventilated area, away from excessive light, heat and

moisture. Keep your monitor away from high-capacity transformers, electric motors, and

other devices with strong magnetic fields.

• In a two-monitor system, place your monitors as far apart from one another as possible to

lessen interference between them.

12

T

ROUBLESHOOTING

You may save time and money by solving common monitor problems using the following simple, easy-

to-apply solutions. If you are unable to solve the problem using these troubleshooting solutions, visit

the Compaq website at

www.compaq.com/athome

www.compaq.com/athomewww.compaq.com/athome

www.compaq.com/athome

or contact your Compaq authorized dealer, reseller,

or service provider.

Problem Possible Cause Solution

Screen is blank Power cord disconnected Connect the power cord

Power switch off Turn on power

Signal cable improperly

connected

Connect signal cable properly

Screen blanking utility is

active

Depress any key on the keyboard or move the mouse

Image appears blurred,

indistinct, or too dark

Brightness and contrast are

too low

Press to access the On-Screen Display (OSD),

then select the brightness and/or contrast

icon to adjust to desired levels*

Color is abnormal A magnetic object may be

nearby

Move the object farther away

Monitor has been moved or

inadvertently bumped

Press to access the OSD, then select

Degauss to activate*

Image is too large or too small Horizontal width may need

adjustment

Press to access the OSD, then select H. Size

to adjust*

Vertical height may need

adjustment

Press to access the OSD, then select V. Size

to adjust*

Image is not centered Horizontal position needs

adjustment

Press to access the OSD, then select H. Position

to adjust*

Vertical position needs

adjustment

Press to access the OSD, then select V. Position

to adjust*

“No Signal” is displayed

on screen

Monitor signal cable is not

connected to the computer

Connect the 15-pin monitor signal cable to the

computer. Be sure that the computer power is on.

“Out of Range” is displayed

on screen

Video resolution and/or

refresh rate are set higher

than what your monitor

supports

Restart your computer, press

F6

before Microsoft

Windows begins to load so that you enter Safe Mode.

Change your settings to a supported setting (see

“Specifications”). Restart your computer so that the

new settings take effect.

*Refer to the “Using Your On-Screen Display” section for detailed instructions. (

continued

)

13

Troubleshooting

(continued)

Problem Possible Cause Solution

No speaker power Speaker power plug may have

come unplugged

Check all speaker power connections and ensure

they are properly connected

Power button on right-side

speaker may be off

Push the power button on the right side of the right

speaker; power button should illuminate

No sound from speakers Speaker audio plug may have

come unplugged from the

back of the computer

Make sure your audio input jack (lime green

connector) is plugged into the back of your computer

Mute button on keyboard may

be activated

Push the mute button on your keyboard or click on

the speaker icon located on your Windows desktop

and deselect “Mute”

Volume level may be adjusted

too low

Increase the volume level by using your keyboard

volume control or clicking on the speaker icon

located on your Windows desktop and increasing the

volume level

No sound from left speaker Speaker connection from left

speaker may have come

unplugged

Make sure the speaker connection from the left

speaker is plugged into the rear of the right speaker

Left speaker balance may

need to be adjusted

Click on the speaker icon located on your Windows

desktop and adjust the Left-Right balance

accordingly

Integrated microphone is

not working

Microphone cable is not

connected properly

Check to ensure that the microphone cable is

connected properly

Monitor is overheating There is not enough

ventilation space to allow

proper airflow

Leave at least 3 inches (76 mm) of ventilation space

surrounding your monitor, and do not place objects

on top of your monitor

14

S

HIPPING

Y

OUR

M

ONITOR

WARNING:

It is strongly recommended that TWO people remove the monitor from its box. This

will help ensure that the monitor is not dropped. Dropping the monitor could cause personal

injury or could damage the monitor.

In the event you need to ship your monitor, keep the original packing box.

If you find it necessary to remove the base pedestal for shipping or service reasons, please refer to the

instructions and illustration below for proper removal.

1. Release the catch and slide the base pedestal toward the back of your monitor.

2. Lift the base pedestal up and away from your monitor.

15

S

PECIFICATIONS

Compaq MV740 Series Color Monitor

Monitor Type Color, multi-frequency, digital controls

Picture Tube 17-inch Flat Square, Polished or Anti-glare

Viewable Image Area 15.9" (405.2 mm)

Operating Temperature 50

°

F – 86

°

F (10

°

C – 30

°

C)

Relative Humidity 20% – 80%

Dot Pitch .28mm

Display Resolutions

1280 x 1024

1024 x 768

800 x 600

720 x 400

640 x 480

640 x 400

Refresh Rates

60 Hz (maximum resolution)

85 Hz (maximum flicker-free resolution)

75 and 60 Hz

85, 75 and 60 Hz

70 Hz

85 and 60 Hz

70 Hz

Input Impedance 75 ± 3 % Ohms

Horizontal Frequency 31.5 kHz – 70 kHz

Vertical Frequency 50 Hz – 120 Hz

Universal Power Supply 90 – 132 V, 50 – 60 Hz

190 – 265 V, 50 – 60 Hz

Inrush Current 30 amps @ 120 V

60 amps @ 220 V

Maximum Power Rating <100 watts

Signal Cable 15-pin miniature D-sub

Speakers (selected models)

Speaker Frequency Response

Speaker Watts

Attachable, amplified JBL Platinum Series

100 Hz – 20 kHz

3W RMS per channel max. at 10% THD

Microphone Integrated

Dimensions (LxWxH) Unpacked 16.4" x 17.8" x 17.7"

(416 mm x 451 mm x 449 mm)

Weight

Unpacked monitor only

Packed in box (Monitor and Speakers)

37.5 lb. (17 kg)

47.40 lb. (21.5 kg)

Power Management Yes

Energy Star Compliant Yes

MPRII Compliant Yes (selected models)

TCO99 Compliant Yes (selected models)

European Union CE Compliant Yes

Plug and Play Yes

16

A

PPENDIX

Regulatory Compliance Notices

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning your equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between your equipment and receiver

• Connect your equipment into an outlet on a circuit different from that to

which the receiver is connected

• Consult the dealer or an experienced radio or television technician for help

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are

not expressly approved by Compaq Computer Corporation may void the user's authority to operate

your equipment.

Cables

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods

in order to maintain compliance with FCC Rules and Regulations.

Declaration of Conformity for products marked with the FCC logo - United States only

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

For questions regarding your product, contact:

Compaq Computer Corporation

P. O. Box 692000, Mail Stop 530113

Houston, Texas 77269-2000

Or, call

1-800-652-6672 (1-800-OK COMPAQ)

17

For questions regarding this FCC declaration, contact:

Compaq Computer Corporation

P. O. Box 692000, Mail Stop 510101

Houston, Texas 77269-2000

Or, call (281) 514-3333

To identify this product, refer to the Part, Series, or Model number found on the product.

Canadian Notice

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

Avis Canadien

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel

brouilleur du Canada.

European Union Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low

Voltage Directive (73/23/EEC) issued by the Commission of the European Community.

Compliance with these directives implies conformity to the following European Norms (in brackets are

the equivalent international standards):

• EN55022 (CISPR 22) - Electromagnetic Interference

• EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity

• EN60950 (IEC950) - Product Safety

• EN60555-2 (IEC555-2) - Power Line Harmonics

EPA Energy Star

Compliance

Monitors that are marked with the ENERGY STAR Logo meet the requirements of the EPA ENERGY

STAR program. As an ENERGY STAR Partner, Compaq Computer Corporation has determined that

this product meets the ENERGY STAR guidelines for energy efficiency. Specific details on using the

Energy Saving features can be found in the energy saver or power management section of the computer

manual.

Japanese Notice

German Ergonomics Notice

Compaq Computers, when tested with the Compaq Monitors, were evaluated and found compliant to

the requirements of ZH 1/618 (German Safety Regulations for Display Work Places in the Office

Sector) in the Text Mode (720 × 400) using MS-DOS Version 3.31 (or higher) and BASICA as

published by Compaq Computer Corporation.

18

A página está carregando...

Compaq 740 Manual do usuário

Este manual também é adequado para

Compaq 740 Manual do usuário

em outras línguas

Artigos relacionados

Outros documentos