ResMed AirCurve 10 Guia de usuario

User guide

English

|

Français

|

Español

|

Português

User guide

English 1

ENGLISH

Welcome

The AirCurve™ 10 VAuto, AirCurve 10 S and AirCurve 10 ST are bilevel positive airway pressure

devices.

WARNING

Read this entire guide before using the device.

CAUTION

In the US, Federal law restricts this device to sale by or on the order of a physician.

Indications for use

AirCurve 10 VAuto

The AirCurve 10 VAuto device is indicated for the treatment of obstructive sleep apnea (OSA) in

patients weighing more than 66 lb (30 kg). It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

AirCurve 10 S

The AirCurve 10 S device is indicated for the treatment of obstructive sleep apnea (OSA) in patients

weighing more than 66 lb (30 kg). It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

AirCurve 10 ST

The AirCurve 10 ST device is indicated for the treatment of obstructive sleep apnea (OSA) in

patients weighing more than 66 lb (30 kg). It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

Contraindications

Positive airway pressure therapy may be contraindicated in some patients with the following

pre-existing conditions:

• severe bullous lung disease

• pneumothorax or pneumomediastinum

• pathologically low blood pressure, particularly if associated with intravascular volume depletion

• dehydration

• cerebrospinal fluid leak, recent cranial surgery, or trauma.

2

Adverse effects

You should report unusual chest pain, severe headache, or increased breathlessness to your

prescribing physician. An acute upper respiratory tract infection may require temporary

discontinuation of treatment.

The following side effects may arise during the course of therapy with the device:

• drying of the nose, mouth, or throat

• nosebleed

• bloating

• ear or sinus discomfort

• eye irritation

• skin rashes.

At a glance

The AirCurve 10 includes the following:

• Device with HumidAir

™

integrated humidifier

• Water tub

• Air tubing

• Power supply unit

• Travel bag

• SD card (not available in all devices).

Contact your care provider for a range of accessories available for use with the device including:

• Air tubing (heated and non-heated): ClimateLineAir

™

, SlimLine

™

, ClimateLineAir Oxy, Standard

• Water tub: Standard water tub, cleanable water tub (can be disinfected)

• Side cover for use without the humidifier

• Filter: Hypoallergenic filter, standard filter

• Air10

™

DC/DC converter

• SD card reader

• Air10 oximeter adapter

• Air10 USB adapter

• Power Station II

• Air10 tubing elbow.

English 3

About your device

1

Air outlet

5

Water tub

2

Air filter cover

6

Screen

3

Power inlet

7

Adapter cover

4

Serial number and device number

8

SD card cover

About the control panel

Start/Stop button

Press to start/stop therapy.

Press and hold for three seconds to enter power save

mode.

Dial

Turn to navigate the menu and press to select an option.

Turn to adjust a selected option and press to save your

change.

Home button Press to return to the Home screen.

Different icons may be displayed on the screen at different times including:

Ramp Time

Wireless signal strength (green)

Humidity

Wireless transfer not enabled (gray)

Humidifier warming

No wireless connection

Humidifier cooling

Airplane Mode

4

Setup

CAUTION

Do not overfill the water tub as water may enter the device and air tubing.

1. Place the device on a stable level surface.

2. Plug the power connector into the rear of the device. Connect one end of the power cord into

the power supply unit and the other end into the power outlet.

3. Connect the air tubing firmly to the air outlet located on the rear of the device.

4. Open the water tub and fill it with distilled water up to the maximum water level mark.

Do not fill the water tub with hot water.

5. Close the water tub and insert it into the side of the device.

6. Connect the free end of the air tubing firmly onto the assembled mask.

See the mask user guide for detailed information.

Recommended masks are available on www.resmed.com.

English 5

Starting therapy

1. Fit your mask.

2. Press Start/Stop or breathe normally if SmartStart

™

is enabled.

You will know that therapy is on when the Sleep Report screen is displayed.

The pressure bar shows the inspiratory and expiratory pressures in green.

The green bar will expand and contract as you breathe in and out.

The screen will go black automatically after a short period of time. You can press Home or the dial to

turn it back on. If power is interrupted during therapy, the device will automatically restart therapy

when power is restored.

The AirCurve 10 device has a light sensor that adjusts the screen brightness based on the light in

the room.

Stopping therapy

1. Remove your mask.

2. Press Start/Stop or if SmartStart is enabled, therapy will stop automatically after a few seconds.

The Sleep Report now gives you a summary of your therapy session.

Usage hours–Indicates the number of hours of therapy you received last

session.

Mask Seal–Indicates how well your mask sealed:

Good mask seal.

Needs adjusting, see Mask Fit.

Humidifier–Indicates if your humidifier is working properly:

Humidifier working.

Humidifier might be faulty, contact your care provider.

If set by your care provider, you will also see:

Events per hour–Indicates the number of apneas and hypopneas experienced per hour.

More Info–Turn the dial to scroll down to view more detailed usage data.

6

Power save mode

Your AirCurve 10 device records your therapy data. In order to allow it to transmit the data to your

care provider, you should not unplug the device. However, you can put it into power save mode to

save electricity.

To enter power save mode:

• Press and hold Start/Stop for three seconds.

The screen goes black.

To exit power save mode:

• Press Start/Stop once.

The Home screen is displayed.

My Options

Your AirCurve 10 device has been set up for your needs by your care provider, but you may find you

want to make small adjustments to make your therapy more comfortable.

Highlight My Options and press the dial to see your

current settings. From here, you can personalize your

options.

Ramp Time

Designed to make the beginning of therapy more comfortable, Ramp Time is the period during

which the pressure increases from a low start pressure to the prescribed treatment pressure.

You can set your Ramp Time to Off or between 5 to 45 minutes.

To adjust Ramp Time:

1. In My Options, turn the dial to highlight Ramp

Time and then press the dial.

2. Turn the dial to adjust the ramp time to your

preferred setting and press the dial to save the

change.

English 7

Humidity Level

The humidifier moistens the air and is designed to make therapy more comfortable. If you are

getting a dry nose or mouth, turn up the humidity. If you are getting any moisture in your mask, turn

down the humidity.

You can set the Humidity Level to Off or between 1 and 8, where 1 is the lowest humidity setting

and 8 is the highest humidity setting.

To adjust the Humidity Level:

1. In My Options, turn the dial to highlight Humidity

Level and then press the dial.

2. Turn the dial to adjust the humidity level and press

the dial to save the change.

If you continue to get a dry nose or mouth, or moisture in your mask, consider using ClimateLineAir

heated air tubing. ClimateLineAir together with Climate Control delivers more comfortable therapy.

Mask Fit

Mask Fit is designed to help you assess and identify possible air leaks around your mask.

To check Mask Fit:

1. Fit the mask as described in the mask user guide.

2. In My Options, turn the dial to highlight Run Mask Fit and then press the

dial.

The device starts blowing air.

3. Adjust the mask, mask cushion and headgear until you get a Good result.

To stop Mask Fit, press the dial or Start/Stop. If you are unable to get a good mask seal, talk to your

care provider.

More options

There are some more options on your device which you can personalize.

Leak Alert*

When Leak Alert is enabled, the device beeps if the mask leaks too much air

or if you remove the mask during therapy.

SmartStart*

When SmartStart is enabled, therapy starts automatically when you breathe

into your mask. When you remove your mask, it stops automatically after a

few seconds.

*When enabled by your care provider.

8

Caring for your device

It is important that you regularly clean your AirCurve 10 device to make sure you receive optimal

therapy. The following sections will help you with disassembling, cleaning, checking and

reassembling your device.

WARNING

Regularly clean your tubing assembly, water tub and mask to receive optimal therapy and to

prevent the growth of germs that can adversely affect your health.

Disassembling

1. Hold the water tub at the top and bottom, press it gently and pull it away from the device.

2. Open the water tub and discard any remaining water.

3. Hold the cuff of the air tubing and gently pull it away from the device.

4. Hold both the cuff of the air tubing and the swivel of the mask, then gently pull apart.

Cleaning

You should clean the device weekly as described. Refer to the mask user guide for detailed

instructions on cleaning your mask.

1. Wash the water tub and air tubing in warm water using only mild detergent.

Do not wash in a dishwasher or washing machine.

2. Rinse the water tub and air tubing thoroughly and allow to dry out of direct sunlight and/or heat.

3. Wipe the exterior of the device with a dry cloth.

English 9

Checking

You should regularly check the water tub, air tubing and the air filter for any damage.

1. Check the water tub:

• Replace it if it is leaking or has become cracked, cloudy or pitted.

• Replace it if the seal is cracked or torn.

• Remove any white powder deposits using a solution of one part household vinegar to

10 parts water.

2. Check the air tubing and replace it if there are any holes, tears or cracks.

3. Check the air filter and replace it at least every six months. Replace it more often if there are any

holes or blockages by dirt or dust.

To replace the air filter:

1. Open the air filter cover and remove the old air filter.

The air filter is not washable or reusable.

2. Place a new air filter onto the air filter cover and then close it.

Make sure the air filter is fitted at all times to prevent water and dust from entering the device.

Reassembling

When the water tub and air tubing are dry, you can reassemble the parts.

1. Connect the air tubing firmly to the air outlet located on the rear of the device.

2. Open the water tub and fill it with distilled room temperature water up to the maximum water

level mark.

3. Close the water tub and insert it into the side of the device.

4. Connect the free end of the air tubing firmly onto the assembled mask.

Therapy data

Your AirCurve 10 device records your therapy data for you and your care provider so they can view

and make changes to your therapy if required. The data is recorded and then transferred to your care

provider wirelessly, if wireless network is available, or via an SD card.

Wireless

Your AirCurve 10 device is equipped with cellular communication. This allows your therapy data to

be wirelessly transmitted to your care provider to enhance the quality of your treatment. It also

allows therapy settings to be updated in a more timely manner or your device software to be

upgraded. The Wireless signal strength icon

displayed at the top right of your screen indicates

the signal strength.

10

The data is usually transmitted after therapy has stopped. In order to make sure that your data is

transferred, leave your device connected to the power outlet at all times and make sure that it is not

in Airplane Mode.

Notes:

• Therapy data might not be transmitted if you use it outside of the country or region of purchase.

• Devices with cellular communication might not be available in all regions.

Please be aware that within the wireless network, the availability and quality of the network may be

affected by terrain, buildings, and the weather. Wireless communication depends on network

availability. Coverage is not available everywhere and varies by service.

SD card

An alternative way for your therapy data to be transferred to your care provider is via the SD card.

Your care provider may ask you to send the SD card by mail or to bring it in. When instructed by

your care provider, remove the SD card.

Do not remove the SD card from the device when the SD light is flashing, because data is being

written to the card.

To remove the SD card:

1. Open the SD card cover.

2. Push in the SD card to release it. Remove the SD card from the device.

Place the SD card in the protective folder and send it back to your care provider.

For more information on the SD card refer to the SD card protective folder provided with your

device.

Note: The SD card should not be used for any other purpose.

Traveling

You can take your AirCurve 10 device with you wherever you go. Just keep the following in mind:

• Use the travel bag provided to prevent damage to the device.

• Empty the water tub and pack it separately in the travel bag.

• Make sure you have the appropriate power cord for the region you are traveling to. For

information on purchasing, contact your care provider.

• If you are using an external battery, you should turn off the humidifier in order to maximize the

life of your battery. Do this by turning the Humidity Level to Off.

English 11

Traveling by plane

Your AirCurve 10 device may be taken on board as carry-on luggage. Medical devices do not count

toward your carry-on luggage limit.

You can use your AirCurve 10 device on a plane as it meets the Federal Aviation Administration

(FAA) requirements. Air travel compliance letters can be downloaded and printed from

www.resmed.com.

When using the device on a plane:

• Make sure the water tub is completely empty and inserted into your device. The device will not

work without the water tub inserted.

• Turn on Airplane Mode.

To turn on Airplane Mode:

1. In My Options, turn the dial to highlight Airplane

Mode and then press the dial.

2. Turn the dial to select On and then press the dial to

save the change.

The Airplane Mode icon

is displayed at the top

right of the screen.

CAUTION

Do not use the device with water in the water tub on a plane due to the risk of inhalation of

water during turbulence.

Troubleshooting

If you have any problems, have a look at the following troubleshooting topics. If you are not able to

fix the problem, contact your care provider or ResMed. Do not try to open the device.

General troubleshooting

Problem/possible cause

Solution

Air is leaking from around my mask

Mask may be fitted incorrectly. Make sure your mask is fitted correctly. See your mask user

guide for fitting instructions or use the Mask Fit function to

check your mask fit and seal.

I am getting a dry or blocked nose

Humidity level may be set too low. Adjust the Humidity Level.

If you have ClimateLineAir heated air tubing, see the

ClimateLineAir user guide.

I am getting droplets of water on my nose, in the mask and air tubing

Humidity level may be set too high. Adjust the Humidity Level.

If you have ClimateLineAir heated air tubing, see the

ClimateLineAir user guide.

12

Problem/possible cause

Solution

My mouth is very dry and uncomfortable

Air may be escaping through your mouth. Increase the Humidity Level.

You may need a chin strap to keep your mouth closed or a

full face mask.

Air pressure in my mask seems too high (it feels like I am getting too much air)

Ramp may be turned off. Use the Ramp Time option.

Air pressure in my mask seems too low (it feels like I am not getting enough air)

Ramp may be in progress. Wait for air pressure to build up or turn Ramp Time off.

My screen is black

Backlight on the screen may have turned off. It turns off

automatically after a short period of time.

Press Home or the dial to turn it back on.

Power may not be connected. Connect the power supply and make sure the plug is fully

inserted.

I have stopped therapy, but the device is still blowing air

Device is cooling down.

Device blows a small amount of air in order to avoid

condensation in the air tubing. It will stop automatically after

30 minutes.

My water tub is leaking

Water tub may not be assembled correctly. Check for damage and reassemble the water tub correctly.

Water tub may be damaged or cracked. Contact your care provider for a replacement.

My therapy data has not been sent to my care provider

Wireless coverage may be poor. Make sure that the device is placed where there is coverage

(ie, on your bedside table, not in a drawer or on the floor).

The Wireless signal strength icon

indicates good

coverage when all bars are displayed, and poor coverage

when fewer bars are displayed.

The No wireless connection icon

is displayed on the

top right of the screen. no wireless network available.

Make sure that the device is placed where there is coverage

(ie, on your bedside table, not in a drawer or on the floor).

If instructed to do so, send the SD card to your care provider.

The SD card also contains your therapy data.

Device may be in Airplane Mode. Turn off Airplane Mode, see Traveling by plane.

Data transfer is not enabled for your device. Talk to your care provider about your settings.

My screen and buttons are flashing

Software upgrade is in progress. Software upgrade takes approximately 10 minutes to

complete.

English 13

Device messages

Device message/possible cause

Solution

High leak detected, check your water tub, tub seal or side cover

Water tub may not be inserted properly. Make sure the water tub is correctly inserted.

Water tub seal may not be inserted properly.

Open the water tub and make sure that the seal is correctly

inserted.

High leak detected, connect your tubing

Air tubing may not be connected properly. Make sure the air tubing is firmly connected at both ends.

Mask may be fitted incorrectly. Make sure your mask is fitted correctly. See your mask user

guide for fitting instructions or use the Mask Fit function to

check your mask fit and seal.

Tubing blocked, check your tubing

Air tubing may be blocked. Check the air tubing and remove any blockages. Press the

dial to clear the message and then press Start/Stop to

restart the device.

SD card error, remove your card and press Start to begin therapy

SD card may not be inserted correctly. Remove and reinsert the SD card.

Read only card, please remove, unlock and re-insert SD card

SD card switch may be in the lock (read-only) position.

Move the switch on the SD Card from the lock position

to the unlock position

and then re-insert it.

All other error messages, for example, System fault, refer to user guide, Error 0XX

An unrecoverable error has occurred on the device. Contact your care provider. Do not open the device.

14

Reassembling parts

Some parts of your device are designed to easily come off in order to avoid damage to the parts or

the device. You can easily reassemble them as described below.

To insert the water tub seal:

1. Place the seal into the lid.

2. Press down along all edges of the seal until it is firmly in place.

To reassemble the water tub lid:

1. Insert one side of the lid into the pivot hole of the base.

2. Slide the other side down the ridge until it clicks into place.

English 15

General warnings and cautions

WARNING

• Make sure that you arrange the air tubing so that it will not twist around the head or neck.

• Make sure the power cord and plug are in good condition and the equipment is not

damaged.

• Keep the power cord away from hot surfaces.

• If you notice any unexplained changes in the performance of the device, if it is making

unusual sounds, if the device or the power supply are dropped or mishandled, or if the

enclosure is broken, discontinue use and contact your care provider or your ResMed

Service Center.

• Do not open or modify the device. There are no user serviceable parts inside. Repairs and

servicing should only be performed by an authorized ResMed service agent.

• Beware of electrocution. Do not immerse the device, power supply or power cord in water.

If liquids are spilled into or onto the device, unplug the device and let the parts dry. Always

unplug the device before cleaning and make sure that all parts are dry before plugging it

back in.

• Supplemental oxygen must not be used while smoking or in the presence of an open

flame.

• Always make sure that the device is turned on and airflow generated before the oxygen

supply is turned on. Always turn the oxygen supply off before the device is turned off, so

that unused oxygen does not accumulate within the device enclosure and create a risk of

fire.

• Do not perform any maintenance tasks while the device is in operation.

• The device should not be used adjacent to or stacked with other equipment. If adjacent or

stacked use is necessary, the device should be observed to verify normal operation in the

configuration in which it will be used.

• The use of accessories other than those specified for the device is not recommended. They

may result in increased emissions or decreased immunity of the device.

• Regularly check the antibacterial filter for signs of moisture or other contaminants,

particularly during nebulization or humidification. Failure to do so could result in increased

breathing system resistance.

CAUTION

• Use only ResMed parts and accessories with the device. Non-ResMed parts may reduce the

effectiveness of the treatment and/or damage the device.

• Use only vented masks recommended by ResMed or by the prescribing doctor with this

device. Fitting the mask without the device blowing air can result in rebreathing of exhaled

air. Make sure that the mask vent holes are kept clear and unblocked to maintain the flow

of the fresh air into the mask.

• Be careful not to place the device where it can be bumped or where someone is likely to

trip over the power cord.

• Blocking the air tubing and/or air inlet of the device while in operation could lead to

overheating of the device.

• Keep the area around the device dry, clean and clear of anything (eg, clothes or bedding)

that could block the air inlet or cover the power supply unit.

• Do not place the device on its side as water might get into the device.

• Incorrect system setup may result in incorrect mask pressure reading. Ensure the system is

correctly set up.

16

• Do not use bleach, chlorine, alcohol, or aromatic-based solutions, moisturizing or

antibacterial soaps or scented oils to clean the device, the water tub or air tubing. These

solutions may cause damage or affect the humidifier performance and reduce the life of

the products. Exposure to smoke, including cigarette, cigar or pipe smoke, as well as ozone

or other gases, may damage the device. Damage caused by any of the foregoing will not

be covered by ResMed's limited warranty.

• If you use the humidifier, always place the device on a level surface lower than your head

to prevent the mask and air tubing from filling with water.

• Leave the water tub to cool for ten minutes before handling to allow the water to cool and

to make sure that the water tub is not too hot to touch.

• Make sure that the water tub is empty before transporting the device.

Technical specifications

90W power supply unit

AC input range:

100–240V, 50–60Hz 1.0–1.5A, Class II

115V, 400Hz 1.5A, Class II (nominal for aircraft use)

DC output:

24V 3.75A

Typical power consumption:

53W (57VA)

Peak power consumption:

104W (108VA)

Environmental conditions

Operating temperature:

+41°F to +95°F (+5°C to +35°C)

Note: The air flow for breathing produced by this therapy

device can be higher than the temperature of the room.

Under extreme ambient temperature conditions

(104°F/40°C) the device remains safe.

Operating humidity:

10 to 95% relative humidity, non-condensing

Operating altitude:

Sea level to 8,500' (2,591 m); air pressure range 1013 hPa to

738 hPa

Storage and transport temperature:

-4°F to +140°F (-20°C to +60°C)

Storage and transport humidity: 5 to 95% relative humidity, non-condensing

Electromagnetic compatibility

The AirCurve 10 complies with all applicable electromagnetic compatibility requirements (EMC) according to

IEC 60601-1-2:2014, for residential, commercial and light industry environments. It is recommended that mobile

communication devices are kept at least 1 m away from the device.

Information regarding the electromagnetic emissions and immunity of this ResMed device can be found on

www.resmed.com/downloads/devices

Classification: IEC 60601-1:2005/A1:2012

Class II (double insulation), Type BF, Ingress protection IP22.

Sensors

Pressure sensor:

Internally located at device outlet, analog gauge pressure

type, 0 to 40 cm H

2

O (0 to 40 hPa)

Flow sensor:

Internally located at device inlet, digital mass flow type, -70

to +180 L/min

Maximum single fault steady pressure

Device will shut down in the presence of a single fault if the steady state pressure exceeds:

30 cm H

2

O (30 hPa) for more than 6 sec or 40 cm H

2

O (40 hPa) for more than 1 sec.

English 17

Sound

Pressure level measured according to ISO 80601-2-70:2015 (CPAP mode):

SlimLine:

25 dBA with uncertainty of 2 dBA

Standard: 25 dBA with uncertainty of 2 dBA

SlimLine or Standard and humidification:

27 dBA with uncertainty of 2 dBA

Power level measured according to ISO 80601-2-70:2015 (CPAP mode):

SlimLine:

33 dBA with uncertainty of 2 dBA

Standard: 33 dBA with uncertainty of 2 dBA

SlimLine or Standard and humidification:

35 dBA with uncertainty of 2 dBA

Declared dual-number noise emission values in accordance with ISO 4871:1996.

Physical - device and water tub

Dimensions (H x W x D):

4.57" x 10.04" x 5.91"

(116 mm x 255 mm x 150 mm)

Air outlet (complies with ISO 5356-1:2015):

22 mm

Weight (device and standard water tub): 44 oz (1248 g)

Weight (device and cleanable water tub):

44 oz (1248 g)

Housing construction: Flame retardant engineering thermoplastic

Water capacity:

To maximum fill line 380 mL

Standard water tub - material: Injection molded plastic, stainless steel and silicone seal

Cleanable water tub - material:

Injection molded plastic, stainless steel and silicone seal

Temperature

Maximum heater plate:

154°F (68°C)

Cut-out:

165°F (74°C)

Maximum gas temperature:

≤ 106°F (≤ 41°C)

Air filter

Standard:

Material: Polyester non woven fiber

Average arrestance: >75% for ~7 micron dust

Hypoallergenic:

Material: Acrylic and polypropylene fibers in a polypropylene

carrier

Efficiency: >98% for ~7-8 micron dust; >80% for ~0.5 micron

dust

Aircraft use

ResMed confirms that device meets the Federal Aviation Administration (FAA) requirements (RTCA/DO-160, section 21,

category M) for all phases of air travel.

Wireless module

Technology used:

CDMA (USA only)

4G (USA and Canada only)

3G

2G (all regions except USA and Canada)

Frequencies

CDMA (850/1900 MHz)

4G (700/850/1900 MHz)

3G (850/900/1700/1800/1900/2100 MHz)

2G (850/900/1800/1900 MHz)

Max RF power output

CDMA 24.5 dBm

4G 23.0 dBm

3G 24.0 dBm

2G 33.0 dBm

18

FCC ID: 2ACHL-AIR104G, 2ACHL-AIR103G

IC: 9103A-AIR104G, 9103A-AIR103G

The AirCurve 10 device complies with FCC Rules and Industry Canada rules.

The AirCurve 10 device should be used at a minimum distance of 0.8" (2 cm) from the body during operation.

Additional information regarding the FCC Rules and IC compliance for this device can be found on

www.resmed.com/downloads/devices

Operating pressure range

S, ST, T:

3 to 25 cm H

2

O (3 to 25 hPa)

VAuto: 4 to 25 cm H

2

O (4 to 25 hPa)

CPAP:

4 to 20 cm H

2

O (4 to 20 hPa)

Supplemental oxygen

Maximum flow:

For VAuto device: 4 L/min (CPAP, S, VAuto)

For S device: 4L/min (CPAP, S)

For ST device: 15 L/min (CPAP, S, ST, T)

Pneumatic flow path

1. Flow sensor

2. Blower

3. Pressure sensor

4. Mask

5. Air tubing

6. Water tub

7. Device

8. Inlet filter

Design life

Device, power supply unit:

5 years

Cleanable water tub: 2.5 years

Standard water tub, air tubing:

6 months

General

The patient is an intended operator.

Humidifier performance

Mask Pressure

cm H

2

O (hPa)

RH output % at

63°F (17°C) ambient

temperature

RH output % at

72°F (22°C) ambient

temperature

Nominal system output AH

1

, BTPS

2

Setting 4

Setting 8

Setting 4

Setting 8

3

85

100

6

>10

4

85

100

6

>10

10

85

100

6

>10

20

85

90

6

>10

25

85

90

6

>10

1

AH - Absolute Humidity in mg/L

2

BTPS - Body Temperature Pressure Saturated

English 19

Air tubing

Material

Length

Inner diameter

ClimateLineAir Flexible plastic and electrical components 6'6" (2 m) 0.6" (15 mm)

ClimateLineAir Oxy

Flexible plastic and electrical components

6'4" (1.9 m)

0.75" (19 mm)

SlimLine Flexible plastic 6' (1.8 m) 0.6" (15 mm)

Standard

Flexible plastic

6'6" (2 m)

0.75" (19 mm)

Heated air tubing temperature cut-out:

≤

106°F (

≤

41°C)

Notes:

• The manufacturer reserves the right to change these specifications without notice.

• The electrical connector end of the heated air tubing is only compatible with the air outlet at the device end and should

not be fitted to the mask.

• Do not use electrically conductive or antistatic air tubing.

• The temperature and relative humidity settings displayed are not measured values.

Displayed values

Value

Range

Display resolution

Pressure sensor at air outlet:

Mask pressure

3–25 cm H

2

O (3–25 hPa)

0.1 cm H

2

O (0.1 hPa)

Flow derived values:

Leak

0–120 L/min

1 L/min

Tidal volume

0–4000 mL

1 mL

Respiratory rate

0–50 bpm

1 bpm

Minute ventilation

0–30 L/min

0.1 L/min

Ti

0.1–4.0 sec

0.1 sec

I:E ratio

1:100–2:1

0.1

Value

Accuracy

1

Pressure measurement

1

:

Mask pressure

2

±[0.5 cm H

2

O (0.5 hPa) + 4% of measured value]

Flow and flow derived values

1

:

Flow ±6 L/min or 10% of reading, whichever is greater, at 0 to 150 L/min positive flow

Leak

2

±12 L/min or 20% of reading, whichever is greater, 0 to 60 L/min

Tidal volume

2,3

± 20%

Respiratory rate

2,3

± 1.0 bpm

Minute ventilation

2,3

± 20%

1

Results are expressed as STPD (Standard Temperature and Pressure, Dry).

2

Accuracy may be reduced by the presence of leaks, supplemental oxygen, tidal volumes <100 mL or minute ventilation <3 L/min.

3

Measurement accuracy verified as per ISO 10651-1:2004 for Home Care Ventilatory Support Devices (Figure 101 and Table 101) using

nominal ResMed mask vent flows.

Measurement system uncertainties

In accordance with ISO 80601-2-70:2015 the measurement uncertainty of the manufacturer's test equipment is:

For measures of flow

± 1.5 L/min or ± 2.7% of reading (whichever is greater)

For measures of volume (< 100 mL) ± 5 mL or 6% of reading (whichever is greater)

For measures of volume (≥ 100 mL)

± 20 mL or 3% of reading (whichever is greater)

For measures of static pressure ± 0.15 cm H

2

O (hPa)

For measures of dynamic pressure

± 0.27 cm H

2

O (hPa)

For measures of time ± 10 ms

Note: ISO 80601-2-70:2015 stated accuracies and test results provided in this manual for these items already include the

relevant measurement uncertainty from the table above.

A página está carregando...

ResMed AirCurve 10 Guia de usuario

ResMed AirCurve 10 Guia de usuario

em outras línguas

Artigos relacionados

Outros documentos