Craftsman CMXEVBE176780 Manual do usuário

Marca: Craftsman

Modelo: CMXEVBE176780

Categoria: Aspirador de pó

Tipo: Manual do usuário

Part No. SP7084 Printed in Mexico

INSTRUCTION MANUAL | GUIDE D’UTILISATION | MANUAL DE INSTRUCCIONES

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1.75 PEAK HP VACUUM POWERHEAD WET/DRY VAC

ASPIRATEUR DE LIQUIDES ET DE POUSSIÈRES

AVEC BLOC-MOTEUR À DÉPRESSION DE 1,75 HP CRÊTE

ASPIRADORA PARA SECO/MOJADO CON CABEZA MOTRIZ

DE ASPIRACIÓN DE 1,75 HP PICO

CMXEVBE176780

1-888-331-4569 WWW.CRAFTSMAN.COM

SP7084-1 CMXEVBE176780.indb 1 8/3/19 7:22 AM

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert symbols and words to alert you to hazardous situations and your risk

of personal injury or property damage.

Components

Fig. A

1 Powerhead Assembly

2 Filter Bag and Retainer Band

3 Inlet Port

4 ON/OFF Switch

5 Power Cord

6 Blowing Port

If you have any questions or comments about this or

any product, call CRAFTSMAN toll free at:

1-888-331-4569.

WARNING: Read all safety

warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock,

fire and/or serious injury.

WARNING: Never modify the

product or any part of it. Damage or personal injury

could result.

WARNING: To reduce the risk of

injury, read the instruction manual.

DANGER: Indicates a hazardous situation which, if not avoided, will result in death or serious

injury.

WARNING: Indicates a hazardous situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a hazardous situation which, if not avoided, may result in minor or moderate

injury.

(Used without word) Indicates a safety related message.

NOTICE: Indicates a practice not related to personal injury which, if not avoided, may result in property damage.

SP7084-1 CMXEVBE176780.indb 2 8/3/19 7:22 AM

IMPORTANT SAFETY INSTRUCTIONS

• This Wet/Dry Vac is not intended for use by persons

(including children) with reduced physical, sensory,

or mental capabilities, or lack of experience and knowledge,

unless they have been given supervision or instruction

concerning use of the appliance by a person responsible

for their safety.

• Do not allow to be used as a toy. Close attention is

necessary when used by or near children.

• Do not use with a torn filter or without the filter

installed except when vacuuming liquids as described

in this manual. Dry debris ingested by the impeller may

damage the motor or be exhausted into the air.

• Turn off Vac before unplugging.

• To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

• Do not unplug by pulling on cord. To unplug, grasp the

plug, not the cord.

• Do not use with damaged cord, plug, or other parts.

If your Vac is not working as it should, has missing parts,

has been dropped, damaged, left outdoors, or dropped

into water, call customer service at 1-888-331-4569

(Mexico 001-881-331-4569).

• Do not pull or carry by cord, use cord as handle, close a

door on cord, or pull cord around sharp edges or corners.

Keep cord away from heated surfaces.

• Do not handle plug, switch, or the Vac with wet hands.

• To reduce the risk of electric shock, use only extension

cords that are rated for outdoor use and have a grounding

conductor. Extension cords in poor condition or too small

in wire size can pose fire and shock hazards. To reduce

the risk of these hazards, be sure the cord is in good

condition and that liquid does not contact the

connection. Do not use an extension cord with

conductors smaller than 1,3 mm2 (16 AWG) in size.

• Connect only to a properly grounded outlet.

See grounding instructions.

• Do not put any object into ventilation openings. Do not

vacuum with any ventilation openings blocked; keep

free of dust, lint, hair, or anything that may reduce air

flow.

• Keep hair, loose clothing, fingers, and all parts of body

away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning

on stairs.

• To reduce the risk of tip-over when carrying by

bucket handle/bale, be sure handle/bale is snapped into

retention notches in latches.

• To reduce the risk of personal injury or damage to Vac,

use only CRAFTSMAN recommended accessories.

• Read and understand this manual and all labels on the

Vac before operating.

• Use only as described in this manual.

• Do not leave Vac running while unattended - you may fail

to notice important signs indicating abnormal operation

such as loss of suction, debris/liquid exiting exhaust, or

abnormal motor noises. Immediately stop using Vac if you

notice these signs.

• Do not leave Vac when plugged in. Unplug from outlet

when not in use and before servicing.

• TO REDUCE THE RISK OF ELECTRIC SHOCK, USE ONLY

BUCKETS WITH THE FOLLOWING UPCs NUMBERS:

ACE® - 0 28901 08836 3,

Amazon - 8 84305 35557 7,

Lowe’s® - 0 51596 10055 1,

Tractor Supply Company® - 0 12891 95001 2,

0 64784 73118 5,

Menards® - 0 17581 30505 9,

CANAC® - 2 01102 14080 3,

Canadian Tire - 6 28076 19101 1,

Orchard Supply Hardware® - 0 26703 05500 0.

The Home Depot® - 0 26703 05555 0, 0 84305 35554 6,

0 62602 00582 1, or 7 501058 561596.

• Sparks inside the motor can ignite flammable vapors or

dust. To reduce the risk of fire or explosion, do not use near

combustible liquids, gases, or dusts, such as gasoline or

other fuels, lighter fluid, cleaners, oil-based paints, natural

gas, coal dust, magnesium dust, grain dust, aluminum

dust, or gun powder. Do not use on a bucket that contains

residuals of such vapors or dusts.

• Do not vacuum anything that is burning or smoking, such as

cigarettes, matches, or hot ashes.

• To avoid the risk of self-ignition of bucket debris, empty

bucket after each use. Combustible materials, such as rags

or saw dust containing stain or urethane, can be sources of

such overheating.

• Do not vacuum drywall dust, cold fireplace ash, or other

fine dusts, which may pass through the filter bag and be

exhausted back into the air.

• To reduce the risk of inhaling toxic vapors, do not vacuum or

use near toxic or hazardous materials.

• To reduce the risk of electric shock, do not expose to rain or

allow liquid to enter motor compartment. Store indoors.

WARNING:

To reduce the risk of fire, electric shock, or injury:

When using this Vac, always follow basic safety

precautions including the following:

SP7084-1 CMXEVBE176780.indb 3 8/3/19 7:22 AM

Observe the following warnings that appear on the motor

housing of your Vac:

WARNING:

• TO REDUCE THE RISK OF INJURY, USER MUST READ

INSTRUCTION MANUAL.

• TO REDUCE THE RISK OF ELECTRIC SHOCK, USE ONLY

BUCKETS WITH THE FOLLOWING UPCs NUMBERS:

ACE® - 0 28901 08836 3,

Amazon - 8 84305 35557 7,

Lowe’s® - 0 51596 10055 1,

Tractor Supply Company® - 0 12891 95001 2,

0 64784 73118 5,

Menards® - 0 17581 30505 9,

CANAC® - 2 01102 14080 3,

Canadian Tire - 6 28076 19101 1,

Orchard Supply Hardware® - 0 26703 05500 0.

The Home Depot® - 0 26703 05555 0,

0 84305 35554 6, 0 62602 00582 1,

or 7 501058 561596.

• Do not leave running while unattended.

• Do not pick up hot ashes, coals, toxic, combustible/

self-igniting, flammable or other hazardous materials,

or use around explosive liquids or vapors, including

residuals leftover in the bucket.

• When using as a blower:

- Direct air discharge only at work area.

- Do not direct air at bystanders.

- Keep children away when blowing.

- Do not use blower for any job except blowing dirt and

debris.

- Do not use as a sprayer.

• To reduce the risk of eye injury, wear safety eyewear.

The operation of any utility Vac or blower can result in

foreign objects being blown into the eyes, which can

result in severe eye damage.

CAUTION:

• To reduce the risk of hearing damage, wear ear

protectors when using for extended time or in a

noisy area.

• For dusty operations, wear dust mask.

• Static shocks are common when the relative

humidity of the air is low. Vacuuming fine

debris with your Vac can deposit static charge

on the hose or Vac. To reduce the frequency of

static shocks in your home or when using this

Vac, add moisture to the air with a humidifier.

• Use only three-wire outdoor extension cords that

have three-prong grounding plugs and grounding

receptacles that accept the appliance’s plug.

• Maintain appliance with care.

WARNING:

To reduce the risk of electric shock - do not expose

to rain - store indoors.

SAVE THESE INSTRUCTIONS

WARNING:

• For your own safety, read and understand Instruction

Manual.

• Do not run unattended.

• Do not pick up hot ashes, coals, toxic, combustible/

self-igniting, flammable or other hazardous materials.

• Do not use around explosive liquids or vapors.

WARNING:

To reduce the risk of personal injury due to a loose

electrical connection between the appliance’s plug and

extension cord, firmly and fully attach the appliance

plug to the extension cord. Periodically check the

connection while operating to ensure it is fully attached.

Do not use an extension cord that provides a loose

connection. A loose connection may result in

overheating, fire, and increases the risk of a burning.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-888-331-4569

for a free replacement.

SP7084-1 CMXEVBE176780.indb 4 8/3/19 7:22 AM

This Powerhead Assembly is intended to be used only with

a 5 U.S. Gallon (19 Liter) plastic bucket, approximately

14-1/2 inches (368 mm) tall with a top diameter of

11-3/4 inches (298 mm) with a 10 gauge steel wire,

bale-type handle.

This bucket is available from many home improvement

locations as listed in the manual.

With this bucket you have a Vac that is intended for

household use.

It may be used for light vacuuming of wet or dry media

and may also be used as a blower. The light-weight design

allows usage for many small household vacuuming chores.

Familiarize yourself with the product and read the

entire instruction manual for specific usage of your new

Wet/Dry Vac.

INTRODUCTION

Section Page

Important Safety Instructions.......................2-4

Introduction .......................................5

Grounding Instructions..............................6

Carton Contents ....................................7

Installation ......................................8-9

Powerhead Assembly .............................8

Powerhead Disassembly...........................8

Insert Hose ......................................9

Power Cord Storage...............................9

Hose Assembly Storage............................9

Operation .....................................10-12

ON/OFF Switch ..................................10

Vacuuming Dry Materials .........................11

Vacuuming Liquids ..............................11

Emptying the Bucket.............................12

Blowing Feature.................................12

Maintenance...................................13-14

Filter Bag Cleaning ..............................13

Filter Bag Removal and Replacement...............13

Storage ........................................13

Cleaning and Disinfecting the Wet/Dry Vac ..........14

Troubleshooting...................................14

Warranty .........................................15

TABLE OF CONTENTS

SP7084-1 CMXEVBE176780.indb 5 8/3/19 7:22 AM

This Vac must be Grounded. If it should malfunction

or break down, Grounding provides a path of least

resistance for Electric Current to reduce the risk of

Electric Shock. This Vac is equipped with a Cord having an

Equipment-Grounding Conductor and Grounding Plug.

The Plug must be inserted into an Appropriate Outlet that

is properly installed and Grounded in accordance with all

Local Codes and Ordinances.

Properly

Grounded

Outlet

Grounding

Prong

3-Prong

Plug

GROUNDING INSTRUCTIONS

Fig. B

WARNING:

Improper connection of the equipment grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service person if you are

in doubt as to whether the outlet is properly grounded.

Do not modify the plug provided with the appliance -

if it will not fit the outlet, have a proper outlet installed

by a qualified electrician.

This Vac is for use on a Nominal 120 Volt Circuit, and has a

Grounded Plug that looks like the Plug shown.

A Temporary Adapter that looks like the Adapter shown

may be used to connect this Plug to a 2-Pole Receptacle,

as shown. If a properly Grounded Outlet is not

available, the Temporary Adapter should be used only

until a properly Grounded Outlet can be installed by a

Qualified Electrician.

The Green Colored Rigid Ear, Lug or the like extending

from the Adapter must be connected to a Permanent

Ground such as a properly Grounded Outlet Box Cover.

Whenever the Adapter is used, it must be held in place

by a Metal Screw.

NOTE: In Canada, the use of a Temporary Adapter is Not

Permitted by the Canadian Electrical Code.

Fig. C

Make sure this is a

metal screw connected

to a known ground

Green

Grounding Lug

Metal

Screw

3-Prong Plug

Adapter

2-Prong Outlet

SP7084-1 CMXEVBE176780.indb 6 8/3/19 7:22 AM

Remove entire contents of carton. Check each item against

the Carton Contents List.

If any parts are damaged or missing, immediately call

Customer Service at 1-888-331-4569

(Mexico 001-881-331-4569).

CARTON CONTENTS (Fig. D)

Fig. D

Key Description Qty.

A Powerhead Assembly 1

B Hose Assembly 1

C Filter Bag 1

D Retainer Band 1

E Instruction Manual 1

Filter Bag and retainer band may already assembled.

NOTE: See Repair Parts List for Part Number.

SP7084-1 CMXEVBE176780.indb 7 8/3/19 7:22 AM

Powerhead Assembly (Figs. E & F)

1. Align the Powerhead Assembly Latches with the

Bucket Handle/Bale.

2. Press down firmly over each Latch to engage the

Latches with the Bucket.

INSTALLATION

Powerhead

Latch (2)

Bucket

Handle/Bale

Fig. E

3. Lift the Bucket Handle/Bale to snap into the Retention

Notches of the Latches.

Fig. F

Powerhead Disassembly (Fig. G)

1. To remove the Powerhead Assembly from the

Bucket, FIRST, unplug the Power Cord from the Wall

Receptacle.

2. Remove the Hose from the Powerhead Assembly and

rotate the Bucket Handle/Bale away from the Power

Cord.

3. Slightly spread both Latches away from the Bucket.

4. Lift the Powerhead Assembly off the Bucket.

NOTE: To reduce the risk of tip-over when carrying by the

Handle/Bale, align the Powerhead Latches above the Bale

attach points and be sure the Bale is snapped into the

Retention Notches on the Latches.

Fig. G

Powerhead

Latch (2)

Bucket

Handle

Power

Cord

Retention

Notch

Powerhead

Latch (2)

Bucket Handle

Retention

Notch

Bail Attach

Point

Powerhead

Latch (2)

Bucket Handle

Retention

Notch

Bale

Attach

Point

Bucket

*Installation shown is for wet pick up applications.

SP7084-1 CMXEVBE176780.indb 8 8/3/19 7:22 AM

Insert Hose (Fig. H)

Insert the Hose Assembly into the Powerhead Assembly

Inlet Port (Located Near the Power Switch). The Hose

should be secure into place.

To remove the Hose Assembly from the Powerhead

Assembly: Twist and pull out on the Hose Assembly to

release the Hose from the Powerhead Assembly Inlet Port.

Hose

Powerhead Assembly

ON/OFF Switch

Powerhead

Assembly

Inlet Port

Fig. H

Hose Assembly Storage (Fig. J)

The Hose Assembly may also be stored inside the Vac

Bucket.

CAUTION:

Do not operate vacuum while the hose or accessories

are stored inside the wet/dry vac’s bucket.

WARNING:

Do not put any object into ventilation openings.

Do not vacuum with any ventilation openings blocked;

keep free of dust, lint, hair or anything that may reduce

air flow.

Power Cord Storage (Fig. I)

The Power Cord should be wrapped around the Powerhead

Assembly.

Snap the Cord Clip onto the Power Cord, to secure in place.

Cord Clip

Power

Cord

Powerhead

Assembly

Fig. I

Hose

Assembly

(Stored

Inside

Bucket)

Fig. J

SP7084-1 CMXEVBE176780.indb 9 8/3/19 7:22 AM

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vac/Blower for extended

time or in a noisy area.

OPERATION

WARNING:

To reduce the risk of electric shock or injury:

• Do not leave Vac running while unattended - you

may fail to notice important signs indicating

abnormal operation such as loss of suction,

debris/liquid exiting the exhaust, or abnormal

motor noises. Immediately stop using Vac if you

notice these signs.

• Do not leave Vac plugged in when not in use.

• Do not continue running when float has cut off

suction.

• Sparks inside the motor can ignite airborne

flammables. Do not operate Vac near

flammable liquids or in areas with flam-

mable gases, vapors, or explosive/

airborne dust. Flammable liquids,

gases, and vapors include: lighter fluid,

solvent-type cleaners, oil-based paints,

gasoline, alcohol, and aerosol sprays. Explosive

dusts include: coal, magnesium, aluminum,

grain, and gun powder.

• Do not vacuum up explosive dusts, flammable

liquids, or hot ashes.

• Do not leave sawdust or rags with stain or

polyurethane residue inside Vac. Empty bucket

after picking up these potentially self-heating

materials.

• Do not expose to rain or allow liquid to enter

motor compartment. Store indoors.

• Do not handle plug, switch, or Vac with wet

hands.

• Unplug Vac before servicing. If your Vac is

not working as it should, has missing parts,

has been dropped, damaged, left outdoors,

or dropped into water, call customer service at

1-888-331-4569 (Mexico 001-881-331-4569).

• When using an extension cord, use only

outdoor-rated cords that are in good condition.

Do not allow the connection to come into contact

with liquid.

= OFF = ON

ON/OFF Switch (Fig. K)

After you Plug the Power Cord into the Outlet, turn the Unit

on by pushing the Switch from position “O” to position “l”.

The symbols used on the Switch Actuator are International

“On & Off” Symbols:

"O" - "OFF"

Position

"I" - "ON"

Position

Fig. K

WARNING:

To reduce the risk of fire, explosion, or dam-

age to Vac:

SP7084-1 CMXEVBE176780.indb 10 8/3/19 7:22 AM

Vacuuming Liquids (Fig. M)

WARNING:

Do not remove the cage and float. The float prevents

liquid from entering the impeller and damaging the

motor. The cage prevents fingers from touching the

moving impeller.

WARNING:

To reduce the risk of fire or explosion, do not vacuum

flammable or combustible liquids, gases or dust.

Vacuuming Dry Materials (Fig. L)

1. The Filter Bag must always be in correct position to

reduce the risk of leaks and possible damage to Vac.

Make sure that the Filter Bag is completely covering

the Filter Cage and that the Retainer Band is as close to

the Powerhead Assembly as possible. Make sure there

are no gaps between the Filter Bag and the Powerhead

Assembly.

NOTE: It is very important to assemble the Filter Bag to

the cage without allowing any possible leaks or tears.

Any leaks will allow the picked up media to be blown

out of the Blower Port and back into the surrounding

environment.

2. When using your Vac to pick up very fine dust,

it will be necessary for you to empty the Bucket and

clean or replace the Filter Bag at more frequent

intervals to maintain peak Vac performance.

See “Replacing the Filter” in the Maintenance section

for complete details.

NOTE: A dry Filter Bag is necessary to pick up dry material.

If you use your Vac to pick up dust when the Filter Bag is

wet, the Filter Bag will clog quickly and be very difficult

to clean. In case the Filter Bag gets wet, replace it before

continuing to do dry pickups.

Fig. L

Retainer

Band

Filter

Bag

Rib Tab

Lid

1. Removal of the Filter Bag is highly recommended for

wet pickups.

2. This Wet/Dry Vac is equipped with a Float Mechanism

which will rise automatically to cut off the airflow when

the liquid in the Bucket reaches a predetermined

level. When this happens, turn OFF Vac, unplug the

Power Cord, and empty the Bucket. You will know that

the Float has shut the airflow off because the suction

ceases and the motor noise becomes higher in pitch,

due to increased motor speed. The liquid capacity may

vary with the rate of pickup.

3. If a Filter Bag was used for wet pickup, be sure to

replace Filter Bag after wet pickup. Never pick up dry

debris without the Filter Bag properly installed.

IMPORTANT: To reduce the risk of damage to the Vac

do not run Motor with Float in raised position.

Fig. M

Float In

Raised

Position

SP7084-1 CMXEVBE176780.indb 11 8/3/19 7:22 AM

1. Remove the Powerhead Assembly: Pull Powerhead

Assembly Latches outward to release from the Bucket.

2. Lift the Powerhead Assembly up and away from the

Bucket.

3. Lay Powerhead Assembly upside down on a clean area

while emptying the Bucket.

4. Dump the Bucket contents into the proper waste

disposal container.

Emptying the Bucket (Fig. N)

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before emptying the bucket.

Fig. N

Bucket

Your Vac features a Blowing Port. It can blow sawdust and

other debris. Follow the following steps to use your Vac

as a Blower.

1. Locate the Blowing Port on the back of your Powerhead

Assembly.

2. Insert one End of the Hose Assembly into the

Powerhead Assembly Blowing Port. The Hose should

be secure into place.

To remove the Hose from the Powerhead Assembly:

Twist and pull out on the Hose Assembly to release the

Hose from the Powerhead Assembly Blowing Port.

3. (Optional) Attach an Accessory to opposite end of

Hose.

4. Turn Powerhead Assembly ON and you are ready to

use your Vac as a Blower.

Blowing Feature (Fig. O)

Fig. O

Blowing Port

Hose

WARNING:

Always wear safety eyewear complying with ANSI Z87.1

(or in Canada, CSA Z94.3) before using as a blower.

WARNING:

To reduce the risk of injury to bystanders, keep them

clear of blowing debris.

CAUTION:

To reduce the risk of hearing damage, wear ear

protectors when using the Vac / Blower for extended

time or in a noisy area.

CAUTION:

Wear a dust mask if blowing creates dust which might

be inhaled.

SP7084-1 CMXEVBE176780.indb 12 8/3/19 7:22 AM

MAINTENANCE

WARNING:

To reduce the risk of injury from accidental starting,

unplug power cord before changing or cleaning filter.

Filter Bag Cleaning

Your Filter should be cleaned often to maintain peak Vac

performance.

After dirty Filter Bag removal from the Powerhead

Assembly, remove the dry debris by gently tapping Filter

against the inside wall of the disposal container.

NOTE: Clean the Filter Bag in an open area. Cleaning

should be done outdoors and not in the living quarters.

IMPORTANT: After cleaning, check the Filter Bag for tears

or small holes. Tears and holes in the Filter Bag can cause

debris and dust to be blown from the Vac. Do not use a Filter

Bag with holes or tears. Replace immediately.

NOTE: See Repair Parts List for Part Number.

NOTE: Before installing the Filter Bag on the Vac, clean the

area of the Powerhead Assembly so that the Retainer Band

will seal the bag against the Powerhead Assembly and stop

small particles from bypassing the Filter Bag.

If the Filter Bag is clean and not damaged, replace it on the

Filter Cage. If it cannot be reused, place a new Filter Bag over

the Filter Cage.

Filter Bag Removal and Replacement

(Fig. P)

IMPORTANT: To avoid damage to the Blower Wheel and

Motor, always reinstall the Filter Bag before using the Vac for

dry material pick-up.

1. Extend the Retainer Band around the Plastic Posts on

the Powerhead Assembly.

2. Remove Filter Bag off the Filter Cage.

3. Place the replacement Filter Bag on the Filter Cage

until open end touches bottom of the Powerhead

Assembly.

4. Release the Retainer Band from the Plastic Post on the

Powerhead Assembly, holding the Filter Bag secure to

the Powerhead Assembly.

5. Make sure the Retainer Band is positioned on the Filter

Bag between the printed lines.

Powerhead

(upside-down)

Filter

Bag

Lid

Retainer Band

Filter Bag

Rib Tab

Lid

Fig. P

Storage

Before storing your Vac, the Bucket should be emptied and

cleaned. The Power Cord should be wrapped around the

Carry Handle and the Hose should be stored as described in

this manual. Accessories should be kept in the same area as

the Vac so they can be readily available. The Vac should be

stored indoors.

SP7084-1 CMXEVBE176780.indb 13 8/3/19 7:22 AM

Troubleshooting

Problem Cause Remedy

Vac will not pick up dirt. 1. Clogged Filter. 1. Clean or replace Filter Bag (Follow instructions on Page 13).

2. Clogged Hose. 2. Remove Hose and clear debris.

3. Air leak. 3. Make sure Powerhead Assembly is securely attached

to Bucket.

Vac will not run. 1. No electricity. 1. Make sure electrical outlet has voltage.

(A qualified electrician may need to be contacted).

Vacuum Powerhead Wet/Dry Vac

Model Number: CMXEVBE176780

Electrical Ratings: 120 V~ 4 A 60 Hz

Replacement Filter Bags are available where you

purchased your Vac.

The Part Number is CMXZVBE38737.

Replacement Filter Bag (Fig. R) Fig. R

WARNING:

To assure product SAFETY and RELIABILITY, any other

maintenance, repairs and adjustments should be

performed by Authorized Service Centers, always using

CRAFTSMAN replacement parts.

Cleaning and Disinfecting the

Wet/Dry Vac

To keep your Wet/Dry Vac looking its best, clean the outside

with a cloth dampened with warm water and mild soap.

To clean the Bucket:

1. Dump debris out.

2. Wash the Bucket thoroughly with warm water and mild

soap.

3. Wipe out with dry cloth.

Before prolonged storage or as needed (i.e., waste water pick

up) the Bucket should be disinfected.

To disinfect the Bucket:

1. Pour 1 gallon (4 L) of water and 1 teaspoon (5 mL)

chlorine bleach into the Bucket.

2. Let solution stand for 20 minutes, carefully swishing

every few minutes, making sure to wet all inside surfaces

of the Bucket.

3. Empty Bucket after 20 minutes. Rinse with water until

bleach smell is gone. Allow Bucket to dry completely

before sealing the Motor on the Bucket.

WARNING:

If any of the powerhead assembly parts should become detached or broken, exposing motor or any other electrical

components, operation should be discontinued immediately to avoid personal injury or further damage to the vacuum.

This vacuum has no user serviceable parts, except the filter.

SP7084-1 CMXEVBE176780.indb 14 8/3/19 7:22 AM

CRAFTSMAN® LIMITED WARRANTY – 3 YEARS

This limited warranty is provided by Emerson Tool Company, a division of Emerson Electric Co., (“We” or “Our” or “Us”) to

the original consumer owner (“Customer” or “You” or “Your”) of the CRAFTSMAN product with which this limited warranty

is provided (the “CRAFTSMAN Product”).

What is Covered

We warrant to You that your CRAFTSMAN Product will be free from defects in materials and workmanship when used

under normal conditions in accordance with the terms of the Instruction Manual provided to You with the CRAFTSMAN

Product, subject to the exclusions described below, for a period of three years commencing on the date of purchase by

You (the “Warranty Period”). This limited warranty terminates if the original purchaser transfers the CRAFTSMAN Product

to any other person or entity.

What is not Covered

This limited warranty does not extend to and expressly excludes:

• Normal wear and tear and/or replacement attachments or accessories, including, without limitation, power cords,

hoses, filters, and other attachments or accessories that may be offered for sale by Us for use with the CRAFTSMAN

Product.

• Damage or burnout of the CRAFTSMAN Product motor resulting from failure to clear a blockage occurring during the

normal course of use.

• Loss or damage to the CRAFTSMAN Product resulting from conditions beyond Our control including without

limitation, misuse, accident, abuse, neglect, negligence (other than Our’s), overuse beyond intended capacity as set

forth in the Instruction Manual, or modifications or alterations made by anyone other than Us.

• Loss or damage to the CRAFTSMAN Product resulting from failure to use the CRAFTSMAN Product in accordance with

the written instructions, guidelines, and terms and conditions set forth in the Instruction Manual.

• TO THE EXTENT PERMITTED BY LAW, IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR

CONSEQUENTIAL DAMAGES, INCLUDING ANY ECONOMIC LOSS, WHETHER RESULTING FROM NONPERFORMANCE,

USE, MISUSE OR INABILITY TO USE THE CRAFTSMAN PRODUCT OR FOR THE NEGLIGENCE OF ETC.

How to Obtain Service

US and Canada – To obtain warranty benefits contact us toll free at 1-888-331-4569 (Mexico 001-881-331-4569).

We will direct you to the nearest service center to review your vacuum for inspection, repairs or replacement.

Mexico - To obtain warranty benefits contact us toll free at 001-881-331-4569. We will direct you to the nearest service

center to review your vacuum for inspection, repairs or replacement.

No Other Express Warranty Applies

This limited warranty is the sole and exclusive warranty provided to You. No other express warranty, written or verbal,

applies including, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.

No employee, agent, dealer, or other person is authorized to alter this limited warranty or make any other warranty on

behalf of Us.

What We will do to Correct Problems

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE LIMITED TO REPAIR, REPLACEMENT,

REFUND OF THE CRAFTSMAN PRODUCT.

After You have contacted CRAFTSMAN Product Customer Service Department, We will initiate warranty proceedings,

including a physical inspection, subject to the exclusions and the Warranty Period stated herein, to determine whether to

repair or replace the CRAFTSMAN Product or provide You with a refund.

The decision to repair or replace your CRAFTSMAN Product or to provide a refund is at Our sole discretion. Repair or

replacements provided to You by ETC are at no cost to You if covered under this limited warranty.

If we are unable to provide You with a suitable repaired or replacement CRAFTSMAN Product, we will provide you with

a refund equal to the purchase price of your CRAFTSMAN Product or a credit to be used toward the purchase of a new

CRAFTSMAN Product.

In the event of any dispute between CUSTOMER AND US, either party may choose to resolve the dispute by binding

arbitration. THIS MEANS IF EITHER CUSTOMER OR US CHOOSE BINDING ARBITRATION, NEITHER PARTY SHALL HAVE THE

RIGHT TO LITIGATE SUCH CLAIM IN COURT OR HAVE A JURY TRIAL. DISCOVERY AND APPEAL RIGHTS ARE LIMITED.

This limited warranty gives you specific legal rights, and you may also have other rights, which vary from State to State.

Some states do not allow the exclusion of incidental or consequential damages, so the above limitation may not apply.

SP7084-1 CMXEVBE176780.indb 15 8/3/19 7:22 AM

Part No. SP7084 Form No. SP7084-1 Printed in Mexico 08/2019

CRAFTSMAN®

is a registered trademark of Stanley Black & Decker, Inc., used under license.

es una marco registrada de Stanley Black & Decker, Inc., utilizada bajo licencio.

est une morque déposée de Stanley Black & Decker, Inc., utilisée sous licence.

2019 CRAFTSMAN

Product Manufactured by: EMERSON TOOL COMPANY

Producto fabricado por: 8100 W. Florissant • St. Louis, MO 63136

Produit fabrriqué par: U.S. & Candaga Only • É.-U. et Canada seulement

SP7084-1 CMXEVBE176780.indb 16 8/3/19 7:22 AM

Fig. A

Définitions : Termes et symboles d’alertes de sécurité

Ce Guide d’utilisation utilise les termes et symboles d’alertes de sécurité suivants pour vous prévenir en cas de situations

dangereuses et de risque de blessures ou de dommages matériels.

En cas de questions ou de commentaires au sujet de ce

produit ou de tout autre produit, téléphonez à CRAFTSMAN

au numéro suivant (appel gratuit) :

1-888-331-4569.

AVERTISSEMENT : Lisez tous les

avertissements relatifs à la sécurité et toutes les instructions

associées. Le non-respect des avertissements et des instructions pourrait

causer un choc électrique, un incendie et/ou des blessures graves.

AVERTISSEMENT : Ne modifiez

jamais le produit ou toute partie de celui-ci. Ceci pourrait causer une

blessure ou des dommages matériels.

AVERTISSEMENT : Pour réduire le

risque de blessure, lisez le Guide d’utilisation.

Composants

1Ensemble du bloc-moteur

2Sac filtrant et bande de retenue élastique

3Orifice d’admission

4Interrupteur de MARCHE/ARRÊT

5Cordon d’alimentation

6Orifice de soufflerie

DANGER : Indique une situation dangereuse imminente qui, si elle n’est pas évitée, causera la mort ou une

blessure grave.

AVERTISSEMENT : Indique une situation pouvant être dangereuse qui, si elle n’est pas évitée,

risque de causer la mort ou une blessure grave.

MISE EN GARDE : Indique une situation dangereuse qui, si elle n’est pas évitée, pourrait causer

une blessure mineure ou modérée.

(Utilisé sans terme) Indique un message relatif à la sécurité.

AVIS : Indique une pratique non associée à un risque de blessure qui, si l’on n’en tient pas compte, pourrait causer des

dommages matériels.

SP7084-1 CMXEVBE176780.indb 17 8/3/19 7:22 AM

• Pour réduire le risque de choc électrique, n’exposez pas à la

pluie et empêchez l’entrée de liquides dans le compartiment

du moteur. Rangez à l’intérieur.

• Cet aspirateur de liquides et de poussières n’est pas conçu pour

emploi par des personnes (y compris des enfants) ayant des

capacités physiques, sensorielles ou mentales réduites, ou qui

n’ont pas l’expérience ou les connaissances nécessaires, sauf

en cas de supervision ou d’instructions sur l’utilisation de cet

appareil par une personne responsable de leur sécurité.

• Ne laissez pas les enfants se servir de l’aspirateur comme d’un

jouet. Il faut surveiller de très près quand il est utilisé par des

enfants ou à proximité d’enfants.

• N’utilisez pas avec un filtre déchiré ou sans avoir installé de filtre,

sauf quand vous aspirez des liquides, comme cela est décrit

dans ce Guide d’utilisation. Des débris secs capturés par la roue

risquent d’endommager le moteur ou d’être expulsés à nouveau

dans l’air ambiant.

• Éteignez l’aspirateur avant de le débrancher.

• Pour réduire le risque de blessure pouvant être causée par

une mise en marche accidentelle, débranchez le cordon

d’alimentation avant de changer le filtre ou de le nettoyer.

• Ne débranchez pas en tirant sur le cordon. Pour débrancher,

saisissez la fiche – pas le cordon.

• N’utilisez pas l’aspirateur avec une fiche, un cordon ou un autre

composant endommagé. Si votre aspirateur ne fonctionne pas

comme il faut, s’il manque des pièces, s’il quelqu’un l’a laissé

tomber, s’il est endommagé, s’il a été laissé à l’extérieur ou s’il

est tombé dans de l’eau, téléphonez au service d’assistance à la

clientèle au 1-888-331-4569 (au Mexique 001-888-331-4569).

• Ne tirez pas l’aspirateur et ne le portez pas par son cordon,

n’utilisez pas le cordon pour servir de poignée, ne fermez pas

une porte sur le cordon et ne laissez pas le cordon tendu passer

sur des bords ou des coins tranchants. Ne traînez pas l’aspirateur

sur son cordon. Maintenez le cordon à distance des surfaces

chauffées.

• Ne touchez pas la fiche, l’interrupteur ou l’aspirateur avec des

mains mouillées.

• N’utilisez que des cordons de rallonge conçus pour un emploi à

l’extérieur et ayant un conducteur de mise à la terre. Les cordons

de rallonge en mauvais état ou dont les diamètres sont trop petits

peuvent poser des risques d’incendie et de choc électrique. Pour

réduire le risque de survenance de tels problèmes, vérifiez que

le cordon est en bon état et qu’aucun liquide ne puisse entrer en

contact avec la connexion. N’utilisez pas de cordon de rallonge

avec des conducteurs de moins de 1,3 mm

(calibre 16 AWG)

de diamètre.

• Raccorder à une prise de courant correctement mise à la terre.

Voir instructions relatives à la mise à la terre.

• Ne mettez aucun objet dans les orifices de ventilation. N’aspirez

pas quand de quelconques orifices de ventilation sont obstrués;

assurez-vous que ces orifices ne sont pas bloqués par de la

poussière, de la peluche, des cheveux ou de quelconques objets

pouvant réduire la circulation de l’air.

• Gardez les cheveux, les vêtements flottants, les doigts et toutes

les parties du corps à distance des orifices et des pièces mobiles.

• Pour réduire le risque de chute, faites très attention lorsque vous

utilisez l’aspirateur dans des escaliers.

• Pour réduire le risque de basculement lorsque vous transportez

l’ensemble par la poignée/l’étrier, assurez-vous que l’étrier est

happé dans les rainures de retenue sur les verrous.

• Lisez et comprenez ce manuel et toutes les étiquettes placées

sur l’aspirateur avant de mettre celui-ci en marche.

• N’utilisez l’aspirateur que comme cela est décrit dans ce

Guide d’utilisation.

• Ne laissez pas en marche pendant que vous êtes absent – vous

vous risqueriez de manquer des signes importants indiquant

un fonctionnement anormal, comme une perte de puissance

d’aspiration, la sortie de débris ou de liquides par la bouche

de soufflage d’air ou des bruits anormaux en provenance du

moteur. Cessez immédiatement d’utiliser l’aspirateur si vous

constatez de tels signes.

• Ne laissez pas l’aspirateur sans surveillance quand il est branché

dans une prise de courant. Débranchez-le de la prise quand il

n’est pas utilisé et avant toute opération de maintenance.

• POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, UTILISEZ

SEULEMENT DES SEAUX AVEC LES NUMÉROS DE RÉFÉRENCE

CUP SUIVANTS :

ACE® – 0 28901 08836 3,

Amazon – 8 84305 35557 7,

Lowe’s® – 0 51596 10055 1,

Tractor Supply Company® – 0 12891 95001 2,

0 64784 73118 5,

Menards® – 0 17581 30505 9,

CANAC® – 2 01102 14080 3,

Canadian Tire – 6 28076 19101 1,

Orchard Supply Hardware® - 26703 05500 0,

The Home Depot® – 0 26703 05555 0,

0 84305 35554 6, 0 62602 00582 1,

ou 7 501058 56159 6.

• Des étincelles à l’intérieur du moteur pourraient mettre le feu

à des vapeurs ou poussières inflammables. Pour réduire le

risque d’incendie ou d’explosion, ne pas utiliser à proximité

de liquides, gaz ou poussières combustibles, comme de

l’essence ou d’autres carburants, de l’essence pour briquets,

des produits de nettoyage, des peintures à base d’huile,

du gaz naturel, de la poussière de charbon, de la poussière

de magnésium, de la poussière céréalière, de la poussière

d’aluminium ou de la poudre noire. N’utilisez pas sur un seau

qui contient des résidus de telles vapeurs ou poussières.

• N’aspirez jamais de quelconques matières en train de

brûler ou des matières fumigènes, telles que des cigarettes,

des allumettes ou des cendres chaudes.

• Videz le seau après chaque utilisation pour éviter le risque

d’auto-inflammation des débris du seau. Les matériaux

combustibles, tels que des chiffons ou de la sciure contenant

des colorants ou de l’uréthane, peuvent être des sources

d’une telle surchauffe.

• N’aspirez jamais de poussières de plaques de plâtre, de suie

ou de cendres de cheminée froides ou de poussières très

fines qui risqueraient d’être projetées à nouveau dans l’air

ambiant.

• Pour réduire le risque d’inhalation de vapeurs toxiques,

n’aspirez pas de matériaux toxiques ou dangereux,

et n’utilisez pas à proximité de tels matériaux.

INSTRUCTIONS IMPORTANTES RELATIVES À LA SÉCURITÉ

Des précautions de sécurité élémentaires doivent être prises

lors de l’utilisation de cet aspirateur, notamment les précautions

suivantes :

AVERTISSEMENT :

Pour réduire le risque d’incendie, de choc électrique

ou de blessure:

SP7084-1 CMXEVBE176780.indb 18 8/3/19 7:22 AM

• Pour réduire le risque de blessure corporelle ou

d’endommagement de l’aspirateur, n’utilisez que des

accessoires compatibles avec la marque CRAFTSMAN.

• En cas d’utilisation de l’aspirateur comme soufflante :

– Ne dirigez la décharge d’air que vers la zone de travail.

– Ne dirigez pas l’air vers des personnes présentes à proximité.

– Gardez les enfants à distance lors du fonction nement de la

soufflante.

– N’utilisez la soufflante que pour souffler des saletés et des

débris.

– N’utilisez pas en guise de pulvérisateur.

• Pour réduire le risque de blessure pour les yeux, portez des

lunettes de sécurité. L’utilisation de toute soufflante ou de tout

aspirateur utilitaire peut toujours causer la projection de corps

étrangers dans les yeux, ce qui risque d’entraîner des blessures

graves aux yeux.

• Utilisez seulement des cordons de rallonge à trois fils prévus

pour emploi à l’extérieur et munis de fiches de mise à la terre

à trois broches ainsi que de prises de mise à la terre qui soient

compatibles avec la fiche de l’appareil.

• Entretenez soigneusement cet appareil.

AVERTISSEMENT :

Pour réduire le risque de blessure pouvant résulter d’une

mauvaise connexion électrique entre la fiche de l’appareil et

le cordon de rallonge, attachez fermement et complète-

ment la fiche de l’appareil au cordon de rallonge. Vérifiez

périodiquement la connexion pendant le fonctionnement

pour assurer qu’elle est solide. Une mauvaise connexion

pourrait causer une surchauffe et même un incendie, et elle

augmenterait le risque de brûlure.

MISE EN GARDE :

• Pour réduire le risque de perte auditive, portez des

protecteurs d’oreilles lorsque vous vous servez de

l’aspirateur pendant plusieurs heures ou quand

vous l’utilisez dans un endroit bruyant.

• Portez un masque antipoussières en cas d’utilisation

dans un environnement poussiéreux.

• Les décharges statiques sont fréquentes dans les

endroits secs ou lorsque l’humidité relative de l’air

ambiant est faible. L’aspiration de débris fins avec

votre aspirateur peut déposer une charge statique

sur le tuyau ou sur l’aspirateur. La meilleure chose

à faire pour réduire la fréquence des décharges

statiques chez vous ou lorsque vous utilisez cet

aspirateur consiste à ajouter de l’humidité dans l’air

avec un humidificateur.

CONSERVER CES INSTRUCTIONS

Observez les avertissements suivants qui figurent sur le carter

du moteur de votre aspirateur :

AVERTISSEMENT :

• Pour votre propre sécurité, lisez et comprenez le manuel de

l’opérateur.

• Ne laissez jamais l’aspirateur en marche sans surveillance.

• Ne ramassez pas de cendres chaudes, de charbon, de

matériaux inflammables, combustibles/auto-inflammables,

de matériaux toxiques ou d’autres matériaux dangereux.

• Ne pas utiliser à proximité de vapeurs ou de liquides

explosifs.

AVERTISSEMENT :

• POUR RÉDUIRE LE RISQUE DE BLESSURE, L’UTILISATEUR

DOIT LIRE LE MODE D’EMPLOI.

• POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE,

UTILISEZ SEULEMENT DES SEAUX AVEC LES NUMÉROS

DE RÉFÉRENCE CUP SUIVANTS :

ACE® – 0 28901 08836 3,

Amazon – 8 84305 35557 7,

Lowe’s® – 0 51596 10055 1,

Tractor Supply Company® – 0 12891 95001 2,

0 64784 73118 5,

Menards® – 0 17581 30505 9,

CANAC® – 2 01102 14080 3,

Canadian Tire – 6 28076 19101 1,

Orchard Supply Hardware® - 26703 05500 0,

The Home Depot® – 0 26703 05555 0,

0 84305 35554 6, 0 62602 00582 1,

ou 7 501058 56159 6.

• Ne laissez pas en marche sans surveillance.

• Ne ramassez pas de cendres chaudes, de charbon,

de matériaux inflammables, combustibles /

auto-inflammables, de matériaux toxiques ou d’autres

matériaux dangereux, et ne l’utilisez pas à proximité de

vapeurs ou de liquides explosifs, y compris des résidus

laissés dans le seau.

AVERTISSEMENT :

Pour réduire le risque de choc électrique — n’exposez pas à

la pluie — rangez à l’intérieur.

REMPLACEMENT GRATUIT DE L’ÉTIQUETTE

D’AVERTISSEMENT : Si vos étiquettes d’avertissement

deviennent illisibles ou sont manquantes, téléphonez au

1-888-331-4569 pour obtenir un remplacement gratuit.

SP7084-1 CMXEVBE176780.indb 19 8/3/19 7:22 AM

Cet ensemble de bloc-moteur ne doit être utilisé qu’avec

un seau en plastique de 19 litres (5 gallons US) d’environ

368 mm (14-1/2 po) de haut, avec un diamètre supérieur

de 298 mm (11-3/4 po) et une poignée en fil d’acier de

calibre 10 de type « balle ». Ce seau est disponible auprès

de nombreux magasins de rénovation indiqués dans le

mode d’emploi. Avec ce seau, vous avez un aspirateur qui

est conçu pour un emploi résidentiel.

Il peut être utilisé pour aspirer de petites quantités de

résidus ou de petits volumes de liquides, et il peut aussi

être employé comme soufflante. Sa conception légère

permet de l’utiliser pour de nombreux petits travaux

d’aspiration à la maison. Familiarisez-vous avec ce produit

et lisez-en tout le mode d’emploi pour apprendre des

usages spécifiques de votre nouvel aspirateur de liquides

et de poussières.

INTRODUCTION

Sujet Page

Instructions importantes relatives à la sécurité .......17-19

Introduction.........................................20

Instructions relatives à la mise à la terre ............21

Contenu de la boîte en carton .........................22

Installation...................................23-24

Montage du bloc-moteur........................23

Démontage du bloc-moteur .....................23

Insertion du tuyau .................................24

Rangement du cordon d’alimentation.............24

Rangement de l’ensemble de tuyau flexible .......24

Fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25-27

Interrupteur de MARCHE/ARRÊT .....................25

Aspiration de matériaux secs ........................26

Aspiration de liquides ..............................26

Vidage du seau ................................27

Fonction de soufflante ..........................27

Entretien .......................................28

Nettoyage du sac filtrant .........................28

Retrait et remplacement du sac filtrant..............28

Rangement .......................................29

Nettoyage et désinfection de l’aspirateur

de liquides et de poussières.......................29

Localisation de la cause des problèmes ...............29

Garantie ............................................30

TABLE DES MATIÈRES

SP7084-1 CMXEVBE176780.indb 20 8/3/19 7:22 AM

A página está carregando ...

Craftsman CMXEVBE176780 Manual do usuário

Marca: Craftsman

Modelo: CMXEVBE176780

Categoria: Aspirador de pó

Tipo: Manual do usuário

baixar PDF

relatório

em outros idiomas

español: Craftsman CMXEVBE176780 Manual de usuario
français: Craftsman CMXEVBE176780 Manuel utilisateur
English: Craftsman CMXEVBE176780 User manual