Kärcher 1.601-990.0 Manual do usuário

8.753-336.0 08/13

K 3.000

®

English 2

Español 17

Français 32

2 English

Model Overview 3

Important Safety Instructions 4

Assembly Instructions 5

Operating Instructions 7

Using the Accessories 8

Working With Detergents 9

Taking a Break 10

Shutting Down & Clean-Up 10

Winterizing and Long-Term Storage 11

Care and Maintenance Instructions 11

Cleaning Tips 12

Optional Cleaning Accessories 13

Troubleshooting 15

K 3.000

Operating Pressure 1800 PSI

Water Volume 1.3 GPM

Amp Draw 13 AMPS

Voltage

120 V

Part No. 1.418-050.0

Serial No.

DANGER

Indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if

not avoided, could result in death or injury.

CAUTION

Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury

or in property damage incidents.

The owner and/or user must have an understand-

ing of the manufacturer’s operating instructions

and warnings before using this pressure washer.

Warning information should be emphasized and

understood.

If the operator is not ﬂ uent in English, the manufac-

turer’s instructions and warnings shall be read to

and discussed with the operator in the operator’s

native language by the purchaser/owner, making

sure that the operator comprehends its contents.

Owner and/or user must study and maintain for

future reference the manufacturer's instructions.

In the U.S. or Canada, please call

1-800-537-4129 for warranty issues and visit

www.karcher-help.com for technical support

and product assistance.

Please take a moment to register your pressure

washer online at www.karcher-register.com.

Be sure to save your purchase receipt, it will be

required for repairs covered by warranty.

Call: 01-800-024-13-13 for help or visit

our website: www.karcher.com.mx

Speciﬁ cations

Owner/User Responsibility

Kärcher Customer Support USA/

Canada

Kärcher Customer Support

Mexico

Safety Alert Symbols

HIGH PRESSURE WASHER OPERATOR MANUAL

For household use only!

English 3

1 Swivel casters

2 ON/OFF switch

3 Detergent tank (removable)

4 High pressure outlet

5 Handle

6 Spray wand and Hp-hose storage

7 Water inlet

8 Water inlet connector

9 Garden hose connector (female)

MODEL OVERVIEW

10 Power cord with Ground Fault Circuit Inter-

rupter (GFCI)

11 Wheels

12 Trigger gun

13 Trigger gun safety lock

14 Quick connect for high pressure hose

15 High pressure hose

16 Vario power spray wand

17 Dirtblaster ® (Rotary spray wand)

4 English

SAVE THESE INSTRUCTIONS

WARNING

When using this product, basic precautions

should always be followed, including the fol-

lowing:

■ Read all the instructions before using the

product.

■ To reduce the risk of injury, close supervision

is necessary when a product is used near

children.

■ Know how to stop the product and bleed pres-

sures quickly. Be thoroughly familiar with the

controls.

■ Stay alert – watch what you are doing.

■ Do not operate the product when fatigued or

under the inﬂ uence of alcohol or drugs.

■ Keep operating area clear of all persons.

■ Do not overreach or stand on unstable sup-

port. Keep good footing and balance at all

times.

■ Follow the maintenance instructions speciﬁ ed

in the manual.

■ This product is provided with a Ground Fault

Circuit Interrupter built into the power cord

plug. If replacement of the plug or cord is

needed, use only identical replacement parts.

WARNING

Risk of Injection or Injury – Do Not Direct

Discharge Stream At Persons.

■ High pressure jets can be dangerous if mis-

used. The jet must not be directed at persons,

animals, electrical devices, or the unit itself.

■ Wear safety goggles.

WARNING

Risk Of Explosion – Do not spray ﬂ ammable

liquids.

■ Do not use acids, solvents, or any ﬂ ammable

or alkaline material in this product. These

products can cause physical injuries to the

operator and irreversible damage to the ma-

chine.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Risk of Electrocution

■ Inspect cord before using – Do not use if cord

is damaged.

■ Keep all connections dry and off the ground.

■ Do not touch plug with wet hands.

■ Do not use extension cord with this product.

■ Connect to individual branch circuit only.

CAUTION

This unit has been designed for use with

cleaning detergents recommended by the

manufacturer. The use of other cleaning

detergents may affect the operation of the

machine and void the warranty.

CAUTION

Gun Kicks Back – Hold with both hands.

■ The Spray Gun Safety Lock prevents the

spray from accidentally being engaged. This

safety feature DOES NOT lock spray in the

ON position.

WARNING

■ Do not spray electrical apparatus and wiring.

■ Do not use with ﬂ ammable liquids or toxic

chemicals.

■ High pressure – keep clear of nozzle.

■ Injection hazard – equipment can cause se-

rious injury if the spray penetrates the skin.

Do not point the gun at anyone or any part of

the body. In case of injury seek medical aid

immediately.

■ This system is capable of producing high

pressure to avoid rupture and injury, do not

operate this pump with accessories rated less

than the stated maximum pressure (including

but not limited to spray guns, hoses and hose

connections).

■ Before servicing, cleaning or removing any

parts, shut off power and relieve pressure.

■ If connection is made to a potable water sys-

tem, the system shall be protected against

back ﬂ ow.

English 5

SERVICING OF A

DOUBLE-INSULATED PRODUCT

WATER SUPPLY

(COLD WATER ONLY)

GROUND-FAULT

CIRCUIT-INTERRUPTER PROTECTION

In a double-insulated product, two systems of

insulation are provided instead of grounding. No

grounding means is provided on a double-insulated

product, nor should a means for grounding be

added to the product. Servicing a double insulated

product requires extreme care and knowledge of

the system, and should be done only by quali-

ﬁ ed service personnel. Replacement parts for a

double-insulated product must be identical to the

parts they replace. A double-insulated product is

marked with the words “DOUBLE INSULATION” or

“DOUBLE INSULATED”. The symbol “



” may also

be marked on the product.

This pressure washer is provided with a ground-

fault circuit-interrupter (GFCI) built into the plug

of the power-supply cord. This device provides

additional protection from the risk of electric shock.

Should replacement of the plug or cord become

necessary, use only identical replacement parts

that include GFCI protection.

CAUTION

When connecting the water inlet to the water sup-

ply mains, local regulations of your water company

must be observed. In some areas the unit must not

be connected directly to the public drinking water

supply. This is to ensure that there is no feedback

of chemicals into the water supply. Direct connec-

tion via a receiver tank or backﬂ ow preventer, for

example, is permitted.

Dirt in the feed water will damage the unit. To avoid

this risk, we recommend ﬁ tting a water ﬁ lter.

■ Garden hose must be at least 1/2 inch or 5/8

inch (13 mm or 16 mm) in diameter.

■ Flow rate of water supply must not fall below

2 GPM (gallons per minute) (7.6 L/min.).

■ Flow rate can be determined by running the

water for one minute into an empty 5 gallon

(20 litre) container.

■ The water supply temperature must not ex-

ceed 40°C/104°F.

■ Never use the pressure washer to draw in

water contaminated with solvents, e.g. paint

thinners, gasoline, oil, etc.

■ Always prevent debris from being drawn into

the unit by using a clean water source.

ASSEMBLY INSTRUCTIONS

Hardware (included)

Item Description Purpose Illustration Qty

A

Rear Wheel Roll Assembly 2

B

Steering

Roller

Roll Assembly 2

C

Adapter Water Inlet Connec-

tion Assembly

1

6 English

STEP 1:

Insert rear wheels into the body of the unit.

STEP 2:

Insert the steering rollers and push until they

click in place.

Assembling

ASSEMBLY INSTRUCTIONS

Hardware (included)

STEP 3:

Install the supplied adaptor to the unit’s water

inlet.

Note: Never attach the garden hose connec-

tor to the unit’s water inlet!

Item Description Purpose Illustration Qty

D

Garden Hose

Connector

Water Inlet Connec-

tion Assembly

1

E

Gun Spray Gun Assembly 1

F

High Pressure

Hose

Spray Gun Assembly 1

G

Vario Power

Spray Wand

Spray Gun Assembly 1

H

Dirtblaster ® Spray Gun Assembly 1

1 2

English 7

STEP 1:

Connect the high pressure hose to the unit’s

high pressure outlet.

STEP 2:

Insert the spray wand of your choice into the

trigger gun. Press in against the spring ten-

sion and twist into locked position.

OPERATING INSTRUCTIONS

STEP 3:

Screw the supplied garden hose connector

on to the end of your garden hose.

STEP 4:

Push the garden hose connector on to the

water inlet connector and make sure you hear

it click into place before proceeding.

STEP 4:

Push the high pressure hose into the trigger

gun until it locks audibly.

Note: Make sure the connection nipple is

aligned correctly.

Check the secure connection by pulling on

the high pressure hose.

Assembling

Disconnect:

Press the disconnect key on the trigger gun

and remove the high pressure hose from the

trigger gun.

8 English

Note: The actual appearance of the GFCI may

be different from this illustration.

STEP 7:

Unlock the trigger gun safety lock. Trigger the

gun to eliminate trapped air, then wait for a

steady ﬂ ow of water to emerge from the spray

nozzle.

STEP 8:

Turn on the high pressure washer by turning

the switch to the (I / ON) position.

The motor runs only while the trigger of the

gun is pulled and shuts off when the trigger

is released.

STEP 5:

Connect garden hose to the cold water source

and turn water on completely.

STEP 6:

Plug the Ground Fault Circuit Interrupter

(GFCI) into a working outlet.

We recommend that you test the GFCI as part

of your startup procedure each time you use

your pressure washer. Plug the GFCI into the

outlet, press the reset button, press the test

button and then press the reset button again.

WARNING

Do not use if above test fails.

USING THE ACCESSORIES

WARNING

To avoid serious injury, never point spray

nozzle at yourself, other persons or animals.

Always test an inconspicuous area before

cleaning with high pressure.

Vario Power Spray Wand

The Vario Power Spray Wand allows you to adjust

the cleaning pressure.

To clean at maximum pressure, the wand must

be positioned to the high pressure setting

(Max).

OPERATING INSTRUCTIONS

For lower pressure turn the wand collar in the

minus (Min) direction.

To apply detergent, the wand must be posi-

tioned to the lower pressure setting (Mix).

English 9

USING THE ACCESSORIES

WORKING WITH DETERGENTS

Dirtblaster®

■ This nozzle features a 0º pencil jet which

rotates 360º for maximum dirt cutting action,

effectively increasing cleaning performance

up to 50%.

This nozzle combines the cleaning perfor-

mance of a 0º pencil jet with the surface

coverage of a wide angle nozzle.

Detergents can only be applied at low pres-

sure setting (Mix).

STEP 1:

Install the Vario Power Spray Wand.

Set the spray wand to the low pressure setting

(Mix).

STEP 2:

Fill the Detergent Tank with the selected

detergent.

STEP 3:

Turn on the pressure washer (I). Pull trigger

to operate unit. Liquid detergent is drawn into

the unit and mixed with water. Apply detergent

to work area. Do not allow detergent to dry

on surface.

STEP 4:

To rinse, move the VPS out of "Mix" position

and pull trigger to operate unit.

STEP 5:

Cleaning up: Always draw fresh water through

the detergent tank or siphon tube when done

to ﬂ ush any remaining detergents from the

injection system.

For best results see Cleaning Tips for speciﬁ c

information on how to clean different surfaces.

Always Use Kärcher ® Detergent for Best

Results.

Kärcher ® biodegradable detergents are specially

formulated to protect the environment and your

pressure washer. The special formula won’t clog

the suction tube ﬁ lter and will protect the internal

parts of the pressure washer for a longer life. For

Kärcher ® detergents, check your retailer or visit

our website:

www.buykarcher.com

CAUTION

Never use:

– Bleach, Chlorine products and other corrosive

chemicals

– Liquids containing solvents (i.e., paint thinners,

gasoline, oils)

– Tri-sodium phosphate products

– Ammonia products

– Acid-based products

These chemicals will harm the unit and will damage

the surface being cleaned.

Use of these items will void the warranty.

Not recommended for soft materials, sid-

ing, painted surfaces, decks or autos.

10 English

TAKING A BREAK ... ﬁ ve minutes or more

SHUTTING DOWN & CLEAN-UP

STEP 1:

Release trigger and engage gun safety lock.

STEP 2:

Turn pressure washer to 0/OFF position

STEP 1:

Turn the switch to 0/OFF position and unplug

cord from outlet.

STEP 2:

Turn off the water source.

STEP 3:

Press trigger to release water pressure.

STEP 4:

Release trigger and engage gun safety lock.

STEP 5:

Disconnect the garden hose from the water

inlet on the unit.

STEP 6:

Disconnect the high pressure hose from the

high pressure outlet.

STEP 7:

Insert the spray wands in their compartments

and store the coiled power cord and coiled

high pressure hose as shown in "WINTER-

IZING AND LONG-TERM STORAGE".

English 11

WINTERIZING AND LONG-TERM STORAGE

CARE AND MAINTENANCE INSTRUCTIONS

1 Disconnect all water connections.

2 Turn the machine on for a few seconds, until

the water which had remained in the pump

exits, then turn off immediately.

3 Do not allow high pressure hose to become

kinked.

4 Store the accessories on the machine as

shown in the picture below, in the following

order:

a. Vario Power Spray Wand and Dirtblaster®.

b. Power cord

c. High Pressure Hose

d. Gun

5 Store the machine and accessories in a room

which does not reach freezing temperatures.

DO NOT store near furnace or other sources

of heat as it may dry out the pump seals.

CAUTION

Failure to follow the above directions will result

in damage to the pump assembly and acces-

sories and will void the warranty. Kärcher®

also recommends the regular practice of

using a pump protector like Kärcher® Pump

Guard (9.558-998.0) to prevent cold weather

damage during storage in the winter months.

Cleaning the water inlet ﬁ lter

Maintenance

STEP 1:

Disconnect the connector from the water inlet.

STEP 2:

Pull out water inlet ﬁ lter with needle-nose

pliers.

STEP 3:

Rinse out water inlet ﬁ lter in warm water.

STEP 4:

Reinsert water inlet ﬁ lter into the water inlet.

The unit is maintenance-free.

a

b

c

d

12 English

CLEANING TIPS

CAUTION

■ Before cleaning any surface, an inconspicu-

ous area should be cleaned to test spray

pattern and distance for maximum cleaning

results.

■ If painted surfaces are peeling or chipping,

use extreme caution as pressure washer may

remove the loose paint from the surface.

■ When using on surfaces which might come in

contact with food, ﬂ ush surfaces with plenty

of drinking water.

■ For additional cleaning tips and a complete

video library, visit our website:

www.karcherresidential.com

Deck Cleaning

House Siding

Cement Patios, Brick and Stone

Cars, Boats and Motorcycles

Barbecue Grills, Outdoor Power

Equipment and Gardening Tools

(with or without detergent) Pre-rinse deck and

surrounding area with fresh water. If using deter-

gent, apply to surface at low pressure. For best

results, limit your work area to smaller sections of

approximately 25 sq. ft. (2.3 m²). Allow detergent

to remain on surface 1-3 minutes. Do not allow

detergent to dry on surface. Rinse at high pres-

sure in a long sweeping motion, keeping the spray

nozzle approximately 3-6 in. (7.5-15 cm) from the

cleaning surface. Always clean from top to bottom

and from left to right. When moving on to a new

section of the cleaning surface, be sure to overlap

the previous section to eliminate stop marks and

ensure a more even cleaning result.

(with or without detergent) Pre-rinse cleaning

surface with fresh water. If using detergent, apply

to surface at low pressure. For best results, limit

your work area to sections of approximately 6 ft.

(1.8 m) and always apply detergent from bottom

to top. Allow detergent to remain on surface 1-3

minutes. Do not allow detergent to dry on surface.

If surface appears to be drying, simply wet down

surface with fresh water. If needed, use special

rotating wash brush (not included) to remove

stubborn dirt. Rinse at high pressure from top to

bottom in an even sweeping motion, keeping the

spray nozzle approximately 6 ft. (1.8 m) from the

cleaning surface.

(with or without detergent) Pre-rinse cleaning

surface with fresh water. If using detergent or

degreaser, apply to surface at low pressure. For

best results, limit your work area to smaller sections

of approximately 25 sq. ft. (2.3 m²). Allow detergent

or degreaser to remain on surface 1-3 minutes. Do

not allow detergent to dry on surface. Rinse at high

pressure in a sweeping motion, keeping the spray

nozzle approximately 3-6 in. (7.5 - 15 cm) from the

cleaning surface. Always clean from top to bottom

and from left to right. For removing extremely stub-

born stains, use the Dirtblaster ® Nozzle.

(with or without detergent) Pre-rinse vehicle with

fresh water. If using detergent, apply to surface at

low pressure. For best results, clean one side of

vehicle at a time and always apply detergent from

bottom to top. Do not allow detergent to dry on

surface. If needed, use a rotating wash brush (not

included) to remove stubborn dirt. Rinse at high

pressure in a sweeping motion, keeping the spray

nozzle approximately 6-8 in. (15-20 cm) from the

cleaning surface (distance should increase when

rinsing pin-striping or other sensitive surfaces).

Always clean from top to bottom and from left

to right. For best results, wipe surface dry with a

chamois or soft dry cloth.

(with or without detergent) Pre-rinse cleaning

surface with fresh water. If using detergent or

degreaser, apply at low pressure. Allow detergent

or degreaser to remain on surface 1-3 minutes. Do

not allow detergent or degreaser to dry on surface.

Rinse at high pressure, keeping the spray nozzle

approximately 3-6 in. (7.5-15 cm) from the cleaning

surface. For removing extremely stubborn dirt, it

may be necessary to move the spray nozzle even

closer to the surface for greater dirt cutting action.

English 13

CLEANING TIPS

OPTIONAL CLEANING ACCESSORIES

Patio and Lawn Furniture

(with or without detergent) Pre-rinse furniture

and surrounding area with fresh water. If using

detergent, apply to surface at low pressure. Allow

detergent to remain on surface 1-3 minutes. Do

not allow detergent to dry on surface. If needed,

use rotating wash brush (not included) to remove

stubborn dirt. Rinse at high pressure in a sweeping

motion, keeping the spray nozzle approximately

3-6 in. (7.5-15 cm) from the cleaning surface. For

best results, clean from top to bottom and from

left to right.

Optional accessories are available to further

enhance your cleaning capabilities. These acces-

sories are accurate as of the printing date of this

manual.

Please check karcherresidential.com for pricing

and up-to-date information.

Pump Guard

Specially formulated to protect your pressure

washer from freezing, corrosion and premature

wear. The Pump Guard also adds lubrication to

valves and seals to prevent sticking. Highly rec-

ommended for all Kärcher ® pressure washers!

Part No. 9.558-998.0

7.5 m (25 ft.) Extension High-

Pressure Hose

Extension Hose for Kärcher ® quick connect high

pressure washers between the original equipment

hose and gun up to 2000 PSI.

Part No. 2.642-588.0

1.67 m (66 in.) Extension Wand

(four-piece)

Need to clean second story windows or other high

areas? Increase the reach of your pressure washer

by up to 66 in. (1.67 m) with this extension kit.

Includes 4 aluminum sections for variable length.

66 in. (1.67 m) fully assembled. Fits most Kärcher®

pressure washers up to 2300 PSI.

Part No. 2.640-746.0

For more effortless cleaning of all smooth surfaces

(painted, glass and plastic) try the Kärcher ®

Rotating Wash Brush. Use it on your automobile,

house siding or windows. The water pressure from

your pressure washer causes the inner brushes to

gently spin, making your cleaning job much easier.

Excellent for the application of detergent. A must-

have accessory designed for Kärcher ® pressure

washers up to 2300 PSI.

Part No. 2.640-907.0

Soft Clean Washing Brush

Made with soft bristles that will not harm painted

surfaces. Easily attaches directly to the trigger

gun. Ideal for stubborn dirt on cars, boats, patio

furniture and other surfaces. Great for applying

detergent. Fits most Kärcher ® pressure washers

up to 2300 PSI.

Part No. 2.640-740.0

7.5 m (25 ft.) Pipe Cleaning Kit

Need to clean blocked pipes, drains or down-

spouts? The Kärcher ® pipe cleaning kit is the

answer! The pipe cleaner propels itself forward

while simultaneously ﬂ ushing out debris. For ex-

ample, insert the cleaning nozzle in the base of a

downspout, pull the trigger on the pressure washer

gun and watch as the nozzle shoots out leaves

and other debris while climbing upward. Connects

directly to the trigger gun of most Kärcher ® pres-

sure washers up to 2300 PSI.

Part No. 2.642-183.0

Rotating Wash Brush

14 English

Wet Sandblasting Kit

Why spend hours stripping old paint and rust by

hand using harsh chemicals? Let the Kärcher ®

Wet Sandblasting Kit do the work! Attach the kit

to your pressure washer, add abrasive material

and attack the rust and paint with our ecofriendly

alternative. Fits most Kärcher ® pressure washers

up to 2300 PSI.

Part No. 2.638-792.0

Detergent Foamer Attachment

Ideal for applications which require a thick foam.

Simply ﬁ ll the resevoir cup with liquid pressure

washer detergent to generate a foam spray. Con-

nects directly to the trigger gun. Fits most Kärcher

® pressure washers up to 2300 PSI.

Part No. 2.642-860.0

T 250 Deck/Driveway Cleaner

For cleaning surfaces such as patios, terraces and

driveways without splashback, there is no better

solution than the Kärcher ® T 250. It saves time

by cleaning a 1 ft. (30 cm) wide area gently as it

hovers, providing consistent, streak-free cleaning.

When you ﬁ nish cleaning the patio and driveway,

remove the wand and use the handle to clean

garage doors and other vertical surfaces. Includes

two nozzles which spin at high speed for optimum

results. Our top selling accessory for Kärcher ®

pressure washers up to 2300 PSI.

Part No. 2.642-451.0

OPTIONAL CLEANING ACCESSORIES

English 15

Symptom Cause Solution

Motor will not

start

On/Off switch is in the

“OFF” (0) position.

Turn switch to the “ON” (I) position

Power cord is not plugged

in.

Plug in power cord.

Electrical outlet does not

supply adequate power.

Try a different outlet.

Tripped GFCI plug. Press “RESET” button on GFCI plug.

Tripped internal circuit

breaker.

Switch off pressure washer. The reset comes

automatically once the temperature of the unit

drops.

Unit does not

reach high

pressure

Diameter of garden hose is

too small.

Replace with a 5/8 inch (16mm) or larger

garden hose.

Water supply is restricted. Check garden hose for kinks, leaks and block-

age.

Not enough inlet water

supply.

Open water source full force.

Water inlet ﬁ lter is clogged. Remove ﬁ lter and rinse out in warm water.

Output pressure

varies high and

low

Not enough inlet water

supply.

Turn water on full force. Check garden hose

for kinks, leaks or blockage.

Pump is sucking air. Check that hoses and ﬁ ttings are air tight.

Turn off machine and purge pump by squeez-

ing trigger gun until a steady ﬂ ow of water

emerges through the nozzle.

Water inlet ﬁ lter is clogged. Remove ﬁ lter and rinse out in warm water.

Discharge nozzle is ob-

structed.

Clean high-pressure nozzle: Remove dirt and

debris from the nozzle bore, using a needle

and rinse through with water from the front.

WARNING

Disconnect the unit from the power source

before making any repair.

TROUBLESHOOTING

16 English

If you encounter any additional difﬁ culties not

listed, please visit our website.

USA / Canada:

www.karcher-help.com

Mexico:

www.karcher.com.mx

Symptom Cause Solution

Detergent not

dispensing

Detergent siphon tube not

properly connected to the

machine.

Check connection.

Detergent is too thick. Dilute detergent, for best results use Kärcher

®

detergent.

Filter on detergent siphon

tube is clogged.

Run warm water through ﬁ lter to remove

debris.

Damaged or clogged deter-

gent siphon tube.

Remove obstruction or replace detergent

siphon tube.

Vario Spray Wand not set

to low/mix setting

Change setting on Vario Power Spray Wand

to "low" or "mix"

Discharge nozzle is ob-

structed.

Blow out or remove debris with ﬁ ne needle.

Garden hose con-

nection leaks

Loose ﬁ ttings. Tighten ﬁ ttings.

Missing/worn rubber

washer.

Insert new washer.

Spray wand leaks.

Spray wand not properly

attached.

Insert the spray wand into the trigger gun.

Carefully press in against the spring tension

and twist into the locked position.

Broken o-ring or plastic

insert.

Call Customer Support

Pump is noisy

Pump is sucking air. Check that hoses and ﬁ ttings are air tight.

Turn off machine and purge pump by squeez-

ing trigger gun until a steady ﬂ ow of water

emerges through the nozzle.

Water leaks from

pump (up to 10

drops per minute

is permissible)

Loose ﬁ ttings. Check that all ﬁ ttings are tight.

Water seals are damaged

or worn.

Call Customer Support

Oil drip

Oil seals are damaged or

worn.

Call Customer Support

Español 17

Descripción general del modelo 18

Instrucciones importantes de seguridad 19

Instrucciones de montaje 20

Instrucciones de funcionamiento 22

Uso de los accesorios 23

Trabajo con detergentes 24

Tomarse un descanso 25

Apagar & recoger 25

Preparación para el Invierno y Almacenaje

de Largo Plazo 26

Instrucciones de cuidado y mantenimiento 26

Consejos de limpieza 27

Accesorios de limpieza opcionales 28

Ayuda en caso de avería 30

K 3.000

Presión de operación 1800 PSI

Volumen de agua 1.3 GPM

Consumo de corriente

en amperes 13 AMPS

Voltaje

120 V

N° de parte 1.418-050.0

N° de serie

PELIGRO

Indica un peligro inminente que, de no evitarse,

resultará en muerte o lesión

grave.

ADVERTENCIA

Indica una situación que puede ser peligrosa y que,

de no evitarse, podría resultar en muerte o lesión.

PRECAUCIÓN

Indica una situación peligrosa que, de no evitarse,

podría resultar lesiones menores o moderadas o

en incidentes de daños a la propiedad.

El propietario y/o usuario debe tener una com-

prensión de las instrucciones de funcionamiento

y avisos de precaución suministrados por el fabri-

cante antes de usar esta hidrolavadora a presión.

La información de precaución debe enfatizarse y

comprenderse correctamente.

Si el operador no habla español, las instrucciones

y precauciones del fabricante deberán leerse y

discutirse junto con el operador en su idioma nativo

por el comprador/propietario, asegurándose de

que el operador comprenda todo el contenido de

las instrucciones.

El propietario y/o usuario deben estudiar las

instrucciones del fabricante y guardarlas para

referencia en el futuro.

Si usted se encuentra en E.E.U.U o en Canadá,

por favor llame al 1-800-537-4129 para asuntos

relacionados con la garantía y visite

www.karcher-help.com si requiere soporte

técnico y ayuda relativa al producto.

Por favor, tómese un momento para registrar su

hidrolavadora a presión en línea en

www.karcher-register.com.

Asegúrese que guardar su recibo de compra ya

que será necesario presentarlo para las repara-

ciones que cubra la garantía.

Llame al: 01-800-024-13-13 para obtener ayuda

o visite

nuestro sitio web: www.karcher.com.mx

Especiﬁ caciones

Responsabilidad del propietario/

usuario

Soporte al cliente de Kärcher en

Estados Unidos/Canadá

Soporte al cliente Kärcher

México

Símbolos de alertas de seguridad

MANUAL DEL OPERADOR PARA LA HIDROLAVADORA DE ALTA PRESIÓN

¡Para uso doméstico únicamente!

18 Español

1 Rueditas giratorias

2 Interruptor encendido/apagado (ON/OFF)

3 Tanque para el detergente (extraíble)

4 Salida de alta presión

5 Agarradera

6 Lanza de agua y almacenamiento de la man-

guera de alta presión

7 Entrada de agua

8 Pieza de acoplamiento para conexión de agua

9 Conector para manguera de jardín (hembra)

DESCRIPCIÓN GENERAL DEL MODELO

10 Cable de alimentación con Interruptor de Cir-

cuito con Falla a Tierra (GFCI, por sus siglas

en inglés)

11 Ruedas

12 Pistola pulverizadora manual

13 Bloqueo de seguridad de la pistola pulveriza-

dora manual

14 Conexión rápida para manguera de alta pre-

sión

15 Manguera de alta presión

16 Lanza de agua Vario Power

17 Dirtblaster ® (Lanza de agua giratoria)

Español 19

GUARDE ESTAS INSTRUCCIONES

ADVERTENCIA

Al usar este producto, deberá seguir en todo

momento ciertas precauciones básicas,

incluidas las siguientes:

■ Lea todas las instrucciones antes de usar el

producto.

■ A ﬁ n de reducir el riesgo de lesiones, será

necesario mantener una supervisión cercana

cuando el producto se use cerca de niños.

■ Sepa cómo detener el producto y descargar

la presión rápidamente. Familiarícese plena-

mente con los controles.

■ Permanezca alerta –vigile lo que esté hacien-

do.

■ No opere el producto cuando esté muy can-

sado o bajo la inﬂ uencia de alcohol o drogas.

■ Mantenga el área de operación despejada

sin personas.

■ No trate de llegar más allá de sus límites y no

se pare sobre un apoyo inestable. Mantenga

sus pies ﬁ rmes en el suelo y equilibrados en

todo momento.

■ Siga las instrucciones de mantenimiento

especiﬁ cadas en este manual.

■ Este producto se proporciona con un Interrup-

tor de circuito con pérdida a tierra integrado

al cable de alimentación. Si llegara a requerir

reemplazar el enchufe o el cable, use única-

mente piezas de recambio idénticas.

ADVERTENCIA

Riesgo de inyección o lesión: No dirija el

chorro de descarga hacia las personas.

■ Los chorros de alta presión pueden ser

peligrosos si se usan incorrectamente. El

chorro no debe apuntarse hacia las persona,

animales, dispositivos eléctricos o al propio

aparato.

■ Use lentes de seguridad.

ADVERTENCIA

Riesgo de explosión: No rocíe líquidos inﬂ a-

mables.

■ No use ácidos, solventes ni ningún otro ma-

terial inﬂ amable o alcalino en este producto.

Estos productos pueden causar lesiones

físicas al operador y daños irreversibles a la

máquina.

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

ADVERTENCIA

Riesgo de electrocución.

■ Inspeccione el cable antes de usarlo. No lo

use si el cable está dañado.

■ Mantenga todas las conexiones secas y

alejadas del suelo.

■ No toque con las manos mojadas.

■ No use un cable de extensión con este pro-

ducto.

■ Conecte a una derivación individual única-

mente.

PRECAUCIÓN

La unidad está diseñada para usarse con de-

tergentes para limpieza recomendados por el

fabricante. El uso de otros detergentes para

limpieza podrían afectar el funcionamiento

de la máquina y anular la garantía.

PRECAUCIÓN

La pistola retrocede. Sostenga con ambas

manos.

■ El seguro de la pistola pulverizadora evita que

el rociado se active accidentalmente. Esta

característica de seguridad NO bloquea el

rociado en la posición ON.

ADVERTENCIA

■ No rocíe aparatos eléctricos ni cableado.

■ No use con líquidos inﬂ amables o químicos

tóxicos.

■ Alta presión: aléjese de la boquilla.

■ Riesgo de inyección: el equipo puede causar

lesiones graves si el rociado penetra la piel.

No apunte la pistola a ninguna persona ni a

ninguna parte del cuerpo. En caso de lesión,

busque atención médica inmediatamente.

■ Este sistema tiene la capacidad de producir

una alta presión para evitar ruptura y lesión,

no opere esta bomba con accesorios cuya

clasiﬁ cación sea menor a la presión máxima

declarada (incluyendo a título enunciativo

mas no limitativo, pistolas pulverizadoras,

mangueras y conectores de mangueras).

■ Antes de reparar, limpiar o extraer cualquier

pieza, apague y deje salir la presión.

■ Si se hace una conexión a un sistema de

agua potable, el sistema debe contar con

protección contra el ﬂ ujo de retorno.

20 Español

MANTENIMIENTO DE UN

PRODUCTO CON DOBLE

AISLAMIENTO

SUMINISTRO DE AGUA

(AGUA FRÍA ÚNICAMENTE)

En los productos con doble aislamiento, se propor-

cionan dos sistemas de aislamiento en vez de una

puesta a tierra. No se suministra puesta a tierra en

un producto de doble aislamiento y tampoco debe-

rán añadirse medios de puesta a tierra al producto.

La reparación de un producto de doble aislamiento

requiere de extremos cuidados y conocimiento del

sistema, y debería llevarse a cabo únicamente

por personal cualiﬁ cado. Las piezas de repuesto

de un producto con doble aislamiento deben ser

idénticas a las piezas que reemplazan. Un producto

de doble aislamiento está marcado con las pala-

bras "DOBLE AISLAMIENTO" o "DOBLEMENTE

AISLADO". El símbolo “



” también podría estar

marcado sobre este producto.

PROTECCIÓN DEL

INTERRUPTOR DE CIRCUITO CON

FALLA A TIERRA

Esta hidrolavadora a presión se suministra con

un interruptor de circuito con falla a tierra (GFCI,

por sus siglas en inglés) integrado en el enchufe

o cable de alimentación. Este dispositivo pro-

porciona protección adicional contra el riesgo de

shock eléctrico. Si llegara a requerir reemplazar

el enchufe o el cable, use únicamente piezas de

recambio que incluyan una protección GFCI.

PRECAUCIÓN

Al conectar la pieza de acoplamiento para co-

nexión de agua a las tomas de suministro de agua,

deberán observarse las normativas locales de su

compañía de agua. En algunas zonas, la unidad

no debe conectarse directamente a un suministro

de agua potable público. Esto es para asegurar

que no se dé retroalimentación de químicos hacia

el suministro de agua. La conexión directa por

medio de un tanque receptor o un desconector,

por ejemplo, sí está permitida.

La suciedad en el suministro de agua dañará la

unidad. Para evitar este riesgo, recomendamos

acoplar un ﬁ ltro de agua.

■ El diámetro de la manguera del jardín debe

ser de 1/2 pulgada o 5/8 pulgadas (13 mm o

16 mm).

■ La tasa del ﬂ ujo del suministro de agua no

debe caer por debajo de 2 GPM (galones por

minuto) (7.6 L/min.).

■ La tasa de ﬂ ujo se puede determinar dejando

correr el agua durante un minuto dentro de

un contenedor vacío de 5 galones (20 litros).

■ La temperatura del suministro de agua no

debe exceder 40°C/104°F.

■ No use nunca la hidrolavadora a presión

para aspirar agua con solventes, por ejemplo

disolventes para pintura, gasolina, aceite, etc.

■ Evite siempre que la unidad jale restos o

escombros, use siempre una fuente de agua

limpia.

INSTRUCCIONES DE MONTAJE

Hardware (incluido)

Artí-

culo Descripción Propósito Ilustración

Can-

tidad

A

Rueda tra-

sera

Montaje para rodaje 2

B

Rueda

giratoria

Montaje para rodaje 2

C

Adaptador Montaje de co-

nexión de entrada

de agua

1

A página está carregando ...

Kärcher 1.601-990.0 Manual do usuário

Kärcher 1.601-990.0 Manual do usuário

em outros idiomas

Artigos relacionados

Outros documentos