Kohler K-RH20910-NA Guia de instalação

Installation and Care Guide

Apron-Front Kitchen Sink

Français, page “Français-1”

Español, página “Español-1”

1317809-2-A

Tools and Materials

Before You Begin

IMPORTANT! Refer to the “Roughing-In” section for cabinet

dimensional requirements.

IMPORTANT! Install this sink before installing the countertop.

Measure the cut-line from the front face of the cabinet.

IMPORTANT! Long screws may damage adjacent cabinets. Ensure

that the screws are long enough to secure the support framing, but

short enough so they do not extend through the walls of adjacent

cabinets.

Due to the nature of under-mount installations, Kohler Co.

recommends that only trained and experienced installers perform

under-mount sink installations.

Use proper fasteners and techniques to ensure that the frame will

support a minimum of 300 lbs (136 kg). Locate the fasteners for

easy access in the event the sink needs to be removed in the

future.

Install this sink into a standard framed 36″ base cabinet.

The countertop manufacturer will provide the anchors and

fasteners.

Observe all local plumbing and building codes.

Plus:

• 2x4s

• Screws

100% Silicone

Sealant

Construction

Adhesive

1317809-2-A 2 Kohler Co.

Roughing-In

17-7/16"

(443 mm)

Apron

1-5/8"

(41 mm)

Front of Cabinet

AB

False Drawer Front

Drawer Opening

B = Top of Cabinet to Top

of Doors

Top of Cabinet to Bottom

of Drawer Opening

A =

Ensure clearance

for faucet installation.

6-11/16"

(170 mm)

Before installing this sink, verify the opening height (A) is

less than the apron height and the distance to the top of

the doors (B) is greater than the apron height.

IMPORTANT!

1-5/8"

(41 mm)

Kohler Co. 3 1317809-2-A

1. Prepare the Cabinet

Remove the false drawer front from your cabinet. Use care to

avoid damaging the cabinet.

Carefully cut away the top rail and center support.

Center

Support

Rail

False Drawer

Front

1317809-2-A 4 Kohler Co.

2. Install Support Framing

NOTICE: For proper countertop installation, the top of the sink

must not extend above the top of the cabinet.

Use 2x4s to construct support framing to extend along the inside

walls on each side of the base cabinet.

Measure and mark the support mounting locations. Make sure

that the sink rim will sit at or slightly below the top of the

cabinet.

Position and level the support framing.

Secure the support framing with construction adhesive and

screws (not provided).

Cut four lengths of 2x4 support framing to extend from the

bottom of the installed supports to the cabinet ﬂoor.

Secure the vertical supports with construction adhesive and

screws (not provided).

Support

Framing

Kohler Co. 5 1317809-2-A

3. Install the Sink

Lower the sink into the cabinet. Verify that the sink is supported

by the frame.

Make sure that the sink is level. Make any necessary adjustments,

and shim as needed.

Remove the sink from the cabinet.

Apply a bead of 100% silicone sealant to the top of each support.

Lower the sink onto the supports, and push in to ensure that the

apron is ﬂush to the front of the cabinet.

1317809-2-A 6 Kohler Co.

4. Install the Countertop

Apply a bead of 100% silicone sealant around the sides and back

of the sink.

Install the countertop.

Kohler Co. 7 1317809-2-A

5. Secure the Sink

NOTE: The countertop manufacturer has preinstalled anchors.

Install the clips to the countertop. Ensure that each clip engages

the rim of the sink. Tighten the clips evenly.

1-5/8"

(41 mm)

1317809-2-A 8 Kohler Co.

6. Complete the Installation

Apply a thin bead of 100% silicone sealant where the sink meets

the countertop and cabinet.

Immediately wipe away any excess sealant.

Care and Cleaning

For best results, keep the following in mind when caring for your

KOHLER product:

•

Always test your cleaning solution on an inconspicuous area

before applying to the entire surface. Cleaners containing chloride

are not recommended.

•

Wipe surfaces clean and rinse completely with water immediately

after applying cleaner. Rinse and dry any overspray that lands on

nearby surfaces.

•

Do not allow cleaners to soak on surfaces.

Kohler Co. 9 1317809-2-A

Care and Cleaning (cont.)

•

Use a soft, dampened sponge or cloth. Never use an abrasive

material such as a brush or scouring pad to clean surfaces.

•

Be careful not to leave staining materials in contact with the

surface for extended periods of time.

•

The ideal cleaning technique is to rinse thoroughly and blot dry

any water from the surface after each use.

For detailed cleaning information and products to consider, visit

www.kohler.com/clean. To order Care & Cleaning information, call

1-800-456-4537.

Warranty

Lifetime Limited Warranty for KOHLER

®

Stainless Steel Sinks

Kohler Co. warrants its stainless steel kitchen, bar, and utility sinks

manufactured after October 24, 2012, to be free of defects in material

and workmanship during normal residential use for as long as the

original consumer purchaser owns his or her home. Gloss reduction,

scratching, staining and acid or alkaline etching of the ﬁnish over time

due to use, cleaning practices or water or atmospheric conditions, are

not manufacturing defects but are indicative of normal wear and tear.

This warranty applies only to KOHLER stainless steel kitchen, bar, and

utility sinks installed in the United States of America, Canada or

Mexico (North America).

If a defect is found in normal residential use, Kohler Co. will, at its

election, repair, replace or make appropriate adjustment. Damage

caused by accident, misuse, or abuse, such as dents and scratches after

installation, is not covered by this warranty. Improper care and

cleaning will void the warranty. Proof of purchase (original sales

receipt) must be provided to Kohler Co. with all warranty claims.

Kohler Co. is not responsible for labor charges, installation, or other

incidental or consequential costs. In no event shall the liability of

Kohler Co. exceed the purchase price of the product.

If the stainless steel kitchen, bar, or utility sink is used commercially or

is installed outside of North America, Kohler Co. warrants the stainless

steel sink to be free from defects in material and workmanship for one

(1) year from the date the product is installed, with all other terms of

this warranty applying except duration. All other components other

than the stainless steel component carry Kohler Co.’s one-year limited

warranty unless otherwise speciﬁed.

If you believe that you have a warranty claim, contact your Dealer,

Plumbing Contractor, Home Center or E-tailer, or write to Kohler at:

1317809-2-A 10 Kohler Co.

Warranty (cont.)

Kohler Co., Attn.: Customer Care Center, 444 Highland Drive, Kohler,

WI 53044, USA. Please be sure to provide all pertinent information

regarding your claim, including a complete description of the problem,

the product, model number, color, ﬁnish, and the date the product was

purchased and from whom the product was purchased. Also include

your original invoice. For other information, or to obtain the name and

address of the service and repair facility nearest you, call

1-800-4-KOHLER (1-800-456-4537) from within the USA and Canada,

and 001-800-456-4537 from within Mexico or visit www.kohler.com

within the USA, www.ca.kohler.com from within Canada, or

www.mx.kohler.com in Mexico.

KOHLER CO. AND/OR SELLER ARE PROVIDING THIS

WARRANTY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED

OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE. KOHLER CO. AND/OR SELLER

DISCLAIMS ANY LIABILITY FOR SPECIAL, INCIDENTAL OR

CONSEQUENTIAL DAMAGES.

Some states/provinces do not allow limitations on how long an

implied warranty lasts or the exclusion or limitation of such damages,

so these limitations and exclusions may not apply to you. This

warranty gives the consumer speciﬁc legal rights. You may also have

other rights that vary from state/province to state/province. This

warranty is to the original consumer purchaser only, and excludes

product damage due to installation error, product abuse, or product

misuse, whether performed by a contractor, service company or the

consumer.

This is Kohler Co.’s exclusive written warranty.

Kohler Co. 11 1317809-2-A

Guide d’installation et d’entretien

Évier avec tablier à l’avant

Outils et matériel

Avant de commencer

IMPORTANT! Se reporter à la section “Raccordement” pour les

conditions requises en matière de dimensions du meuble.

IMPORTANT! Installer cet évier avant d’installer le comptoir.

Mesurer la ligne de découpe à partir de la face avant du meuble.

IMPORTANT! Les vis longues peuvent endommager les meubles

adjacents. S’assurer que les vis sont suffisamment longues pour ﬁxer

la charpente de support, mais suffisamment courtes pour ne pas

traverser les parois des meubles adjacents.

En raison de la nature des installations à montage sous plan,

Kohler Co. recommande que seuls les installateurs formés et

ayant de l’expérience effectuent des installations à montage sous

plan.

Utiliser les dispositifs d’attache et les techniques qui conviennent

pour assurer que le cadre puisse soutenir un minimum de 300 lb

(136 kg). Placer les dispositifs d’attache à des endroits auxquels

accéder sans difficulté au cas où l’évier devait être déposé à

l’avenir.

Installer cet évier dans un meuble de base de 36″ encadré

standard.

Plus:

• Montants 2x4

• Vis

Mastic à la

silicone à 100%

Adhésif de

construction

Kohler Co. Français-1 1317809-2-A

Avant de commencer (cont.)

Le fabricant du comptoir fournira les dispositifs d’ancrage et

d’attache.

Respecter tous les codes de plomberie et de bâtiment locaux.

Kohler Co. Français-2 1317809-2-A

Raccordement

17-7/16"

(443 mm)

Tablier

1-5/8"

(41 mm)

Avant du meuble

AB

Avant du faux tiroir

Ouverture du tiroir

B = Dessus du meuble jusqu'au

dessus des portes

Dessus du meuble jusqu'au

fond de l'ouverture du tiroir

A =

Assurer un dégagement

pour l'installation

du robinet.

6-11/16"

(170 mm)

Avant d'installer cet évier, vérifier que la hauteur de

l'ouverture (A) est inférieure à la hauteur du tablier et que la

distance jusqu'au dessus des portes (B) est supérieure à la

hauteur du tablier.

IMPORTANT!

1-5/8"

(41 mm)

1317809-2-A Français-3 Kohler Co.

1. Préparer le meuble

Retirer la façade de faux-tiroir du meuble. Procéder avec

précaution pour éviter d’endommager le meuble.

Couper avec précaution le rail supérieur et le support central.

Support

central

Rail

Avant du

faux tiroir

Kohler Co. Français-4 1317809-2-A

2. Installer la charpente de support

AVIS: Pour assurer une installation correcte du comptoir, le dessus

de l’évier ne doit pas dépasser du dessus du meuble.

Utiliser des montants 2x4 pour construire une charpente de

support qui se prolongera le long des murs intérieurs sur chaque

côté du meuble de base.

Mesurer et marquer les emplacements de montage du support.

S’assurer que le rebord de l’évier se trouve au ras ou légèrement

en dessous du haut du meuble.

Positionner et mettre la charpente de support de niveau.

Fixer la charpente de support avec de l’adhésif de construction et

des vis (non fournies).

Découper quatre longueurs de charpente de support 2x4 à

prolonger entre le dessous des supports installés et le plancher du

meuble.

Fixer les supports verticaux avec de la colle de construction et des

vis (non fournies).

Charpente de

support

1317809-2-A Français-5 Kohler Co.

3. Installer l’évier

Abaisser l’évier dans le meuble. Vériﬁer que l’évier est supporté

par le cadre.

S’assurer que l’évier est de niveau. Effectuer tous les ajustements

nécessaires et caler au besoin.

Retirer l’évier du meuble.

Appliquer un boudin de mastic à la silicone à 100% sur le dessus

de chaque support.

Abaisser l’évier sur les supports et enfoncer pour assurer que le

bandeau soit à ras de l’avant du meuble.

Kohler Co. Français-6 1317809-2-A

4. Installer le comptoir

Appliquer un cordon de mastic à la silicone à 100% autour des

côtés et de l’arrière de l’évier.

Installer le comptoir.

1317809-2-A Français-7 Kohler Co.

5. Fixer l’évier en place

REMARQUE: Le fabricant du comptoir a fourni des dispositifs

d’ancrage préinstallés.

Installer les agrafes sur le comptoir. S’assurer que chaque agrafe

s’engage sur le rebord de l’évier. Serrer les attaches de manière

uniforme.

1-5/8"

(41 mm)

Kohler Co. Français-8 1317809-2-A

6. Terminer l’installation

Appliquer un mince cordon de mastic à la silicone à 100% aux

endroits où l’évier touche le comptoir et le meuble.

Essuyer immédiatement tout excédent de mastic d’étanchéité.

Entretien et nettoyage

Pour obtenir les meilleurs résultats possibles, prendre ce qui suit en

considération lors de l’entretien de votre produit KOHLER:

•

Toujours tester la solution de nettoyage sur une surface non

visible avant de l’appliquer sur l’ensemble de la surface. Les

nettoyants qui contiennent du chlorure ne sont pas recommandés.

•

Essuyer les surfaces et rincer complètement avec de l’eau

immédiatement après l’application du nettoyant. Rincer et sécher

tout éclaboussement sur les surfaces avoisinantes.

•

Ne pas laisser les nettoyants tremper sur les surfaces.

1317809-2-A Français-9 Kohler Co.

A página está carregando ...

Kohler K-RH20910-NA Guia de instalação

Kohler K-RH20910-NA Guia de instalação

em outros idiomas

Artigos relacionados

Outros documentos