Yamaha HD-300 Manual do proprietário

Marca: Yamaha

Modelo: HD-300

Tipo: Manual do proprietário

Owner’s Manual

Mode d’emploi

Manual de instrucciones

Benutzerhandbuch

EnglishFrançaisEspañolDeutsch

HARMONY DIRECTOR™

HD-300 Owner’s Manual

The model number, serial number, power requirements, etc., may be

found on or near the name plate, which is at the bottom of the unit.

You should note this serial number in the space provided below and

retain this manual as a permanent record of your purchase to aid iden-

tification in the event of theft.

Model No.

Serial No.

(bottom_en_01)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions

contained in this manual, meets FCC requirements. Modifica-

tions not expressly approved by Yamaha may void your

authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories

and/or another product use only high quality shielded cables.

Cable/s supplied with this product MUST be used. Follow all

installation instructions. Failure to follow instructions could

void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply

with the requirements listed in FCC Regulations, Part 15 for

Class “B” digital devices. Compliance with these require-

ments provides a reasonable level of assurance that your

use of this product in a residential environment will not result

in harmful interference with other electronic devices. This

equipment generates/uses radio frequencies and, if not

installed and used according to the instructions found in the

users manual, may cause interference harmful to the opera-

tion of other electronic devices. Compliance with FCC regula-

tions does not guarantee that interference will not occur in all

installations. If this product is found to be the source of inter-

ference, which can be determined by turning the unit “OFF”

and “ON”, please try to eliminate the problem by using one of

the following measures:

Relocate either this product or the device that is being

affected by the interference.

Utilize power outlets that are on different branch (circuit

breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the

antenna. If the antenna lead-in is 300 ohm ribbon lead,

change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory

results, please contact the local retailer authorized to distrib-

ute this type of product. If you can not locate the appropriate

retailer, please contact Yamaha Corporation of America,

6600 Orangethorpe Ave, Buena Park, CA90620, USA

The above statements apply ONLY to those products distrib-

uted by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by Yamaha Corporation of America. (class B)

FCC INFORMATION (U.S.A.)

* This applies only to products distributed by Yamaha Corporation of America.

COMPLIANCE INFORMATION STATEMENT (Supplierʼs declaration of conformity procedure)

Responsible Party: Yamaha Corporation of America

Address: 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone: 714-522-9011

Type of Equipment: HARMONY DIRECTOR

Model Name: HD-300

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

(FCC SDoC)

HD-300 Owner’s Manual

(weee_battery_eu_en_02)

Information for users on collection and disposal of old equipment and used batteries

These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic

products and batteries should not be mixed with general household waste.

For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection

points, in accordance with your national legislation.

By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential

negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products and batteries, please contact your local municipality, your

waste disposal service or the point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union:

These symbols are only valid in the European Union. If you wish to discard these items, please contact your local authorities

or dealer and ask for the correct method of disposal.

Note for the battery symbol (bottom two symbol examples):

This symbol might be used in combination with a chemical symbol. In this case it complies with the requirement set by the EU

Battery Directive for the chemical involved.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol

within an equilateral triangle is intended to alert

the user to the presence of uninsulated

“dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to

constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug has

two blades and a third grounding prong. The wide blade

or the third prong are provided for your safety. If the

provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the

point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand,

tripod, bracket, or table

specified by the manufacturer,

or sold with the apparatus.

When a cart is used, use caution

when moving the cart/apparatus

combination to avoid injury from

tip-over.

13 Unplug this apparatus during lightning storms or when

unused for long periods of time.

14 Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have

fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

English

For AC adaptor

For AC adaptor and the instrument

HD-300 Owner’s Manual

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING

• This AC adaptor is designed for use with only Yamaha

electronic instruments. Do not use for any other purpose.

• Indoor use only. Do not use in any wet environments.

CAUTION

• When setting up, make sure that the AC outlet is easily

accessible. If some trouble or malfunction occurs, immediately

turn off the power switch of the instrument and disconnect the

AC adaptor from the outlet. When the AC adaptor is connected

to the AC outlet, keep in mind that electricity is flowing at the

minimum level, even if the power switch is turned off. When you

are not using the instrument for a long time, make sure to

unplug the power cord from the wall AC outlet.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from

electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited

to, the following:

• Do not place the power cord near heat sources such as heaters

or radiators. Also, do not excessively bend or otherwise damage

the cord, or place heavy objects on it.

• Only use the voltage specified as correct for the instrument. The

required voltage is printed on the name plate of the instrument.

• Use the specified adaptor (page 40) only. Using the wrong

adaptor can result in damage to the instrument or overheating.

• Check the electric plug periodically and remove any dirt or dust

which may have accumulated on it.

• This instrument contains no user-serviceable parts. Do not

open the instrument or attempt to disassemble or modify the

internal components in any way. If it should appear to be

malfunctioning, discontinue use immediately and have it

inspected by qualified Yamaha service personnel.

• Do not expose the instrument to rain, use it near water or in

damp or wet conditions, or place on it any containers (such as

vases, bottles or glasses) containing liquids which might spill

into any openings. If any liquid such as water seeps into the

instrument, turn off the power immediately and unplug the

power cord from the AC outlet. Then have the instrument

inspected by qualified Yamaha service personnel.

• Never insert or remove an electric plug with wet hands.

• Do not put burning items, such as candles, on the unit.

A burning item may fall over and cause a fire.

• Radio waves may affect electro-medical devices.

- Do not use this product near medical devices or inside areas

in which the use of radio waves is restricted.

- Do not use this product within 15cm (6 in.) of persons with a

heart pacemaker or defibrillator implant.

For AC adaptor

For the instrument

Power supply/AC adaptor

Do not open

Water warning

Fire warning

Influences on electro-medical devices

DMI-7 1/2

HD-300 Owner’s Manual

• Follow the precautions below. Failure to do so might result in

explosion, fire, overheating or battery fluid leakage.

- Do not tamper with or disassemble batteries.

- Do not dispose of batteries in fire.

- Do not attempt to recharge batteries that are not designed to

be charged.

- Keep the batteries separate from metallic objects such as

necklaces, hairpins, coins, and keys.

- Use the specified battery type (page 40) only.

- Use new batteries, all of which are the same type, same model,

and made by the same manufacturer.

- Always make sure all batteries are inserted in conformity with

the +/- polarity markings.

- When the batteries run out, or if the instrument is not to be

used for a long time, remove the batteries from the instrument.

- When using Ni-MH batteries, follow the instructions that came

with the batteries. Use only the specified charger device when

charging.

• Keep batteries away from small children who might accidentally

swallow them.

• If the batteries do leak, avoid contact with the leaked fluid. If the

battery fluid should come in contact with your eyes, mouth, or

skin, wash immediately with water and consult a doctor. Battery

fluid is corrosive and may possibly cause loss of sight or

chemical burns.

• When one of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet. (If you are using batteries, remove all batteries from the

instrument.) Then have the device inspected by Yamaha service

personnel.

- The power cord or plug becomes frayed or damaged.

- It emits unusual smells or smoke.

- Some object has been dropped into the instrument.

- There is a sudden loss of sound during use of the instrument.

- If any cracks or breakages exist on the instrument.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or

damage to the instrument or other property. These precautions include, but are not limited to, the following:

• Do not connect the instrument to an electrical outlet using a

multiple-connector. Doing so can result in lower sound quality,

or possibly cause overheating in the outlet.

• When removing the electric plug from the instrument or an

outlet, always hold the plug itself and not the cord. Pulling by

the cord can damage it.

• Remove the electric plug from the outlet when the instrument is

not to be used for extended periods of time, or during electrical

storms.

• Do not place the instrument in an unstable position where it

might accidentally fall over.

• Before moving the instrument, remove all connected cables, to

prevent damage to the cables or injury to anyone who might trip

over them.

• When setting up the product, make sure that the AC outlet you

are using is easily accessible. If some trouble or malfunction

occurs, immediately turn off the power switch and disconnect

the plug from the outlet. Even when the power switch is turned

off, electricity is still flowing to the product at the minimum

level. When you are not using the product for a long time, make

sure to unplug the power cord from the wall AC outlet.

• Before connecting the instrument to other electronic

components, turn off the power for all components. Before

turning the power on or off for all components, set all volume

levels to minimum.

• Be sure to set the volumes of all components at their minimum

levels and gradually raise the volume controls while playing the

instrument to set the desired listening level.

• Do not insert a finger or hand in any gaps on the instrument.

• Never insert or drop paper, metallic, or other objects into the

gaps on the panel or keyboard. This could cause physical injury

to you or others, damage to the instrument or other property, or

operational failure.

• Do not rest your weight on, or place heavy objects on the

instrument, and do not use excessive force on the buttons,

switches or connectors.

• Do not use the instrument/device or headphones for a long

period of time at a high or uncomfortable volume level, since

this can cause permanent hearing loss. If you experience any

hearing loss or ringing in the ears, consult a physician.

Yamaha cannot be held responsible for damage caused by

improper use or modifications to the instrument, or data that

is lost or destroyed.

Always turn the power off when the instrument is not in use.

Even when the [] (Standby/On) switch is in standby status

(display is off), electricity is still flowing to the instrument at the

minimum level.

When you are not using the instrument for a long time, make sure

you unplug the power cord from the wall AC outlet.

Make sure to discard used batteries according to local regulations.

Battery

If you notice any abnormality

Power supply/AC adaptor

Location

Connections

Handling

DMI-7 2/2

HD-300 Owner’s Manual

NOTICE

To avoid the possibility of malfunction/ damage to the

product, damage to data, or damage to other property,

follow the notices below.

 Handling

• Do not use the instrument in the vicinity of a TV, radio,

stereo equipment, mobile phone, or other electric

devices. Otherwise, the instrument, TV, or radio may

generate noise. When you use the instrument along

with an application on your smart device such as a

smartphone or tablet, we recommend that you set

Bluetooth to on after enabling “Airplane Mode” on that

device in order to avoid noise caused by

communication.

• Do not expose the instrument to excessive dust or

vibrations, or extreme cold or heat (such as in direct

sunlight, near a heater, or in a car during the day) to

prevent the possibility of panel disfiguration, damage

to the internal components or unstable operation.

• Do not place vinyl, plastic or rubber objects on the

instrument, since this might discolor the panel or

keyboard.

 Maintenance

• When cleaning the instrument, use a soft cloth. Do not

use paint thinners, solvents, alcohol, or chemical-

impregnated wiping cloths.

 Saving data

• Some of settings of this instrument are retained when

the power is turned off. However, the saved settings

may be lost due to some failure, an operation mistake,

etc.

Information

 About copyrights

• Copying of the commercially available musical data

including but not limited to MIDI data and/or audio

data is strictly prohibited except for your personal use.

• This product incorporates and bundles contents in

which Yamaha owns copyrights or with respect to

which Yamaha has license to use others’ copyrights.

Due to copyright laws and other relevant laws, you are

NOT allowed to distribute media in which these

contents are saved or recorded and remain virtually the

same or very similar to those in the product.

* The contents described above include a computer

program, MIDI data, WAVE data, voice recording

data, a score, score data, etc.

* You are allowed to distribute medium in which your

performance or music production using these

contents is recorded, and the permission of Yamaha

Corporation is not required in such cases.

 About functions/data bundled with the

instrument

• This device is capable of using various types/formats of

music data by optimizing them to the proper format

music data for use with the device in advance. As a

result, this device may not play them back precisely as

their producers or composers originally intended.

 About this manual

• The illustrations and LCD screens as shown in this

manual are for instructional purposes only, and may

appear somewhat different from those on your

instrument.

• Windows is a registered trademark of Microsoft®

Corporation in the United States and other countries.

• Mac, iPhone, and iPad are trademarks of Apple Inc.,

registered in the U.S. and other countries.

• The Bluetooth® word mark and logos are registered

trademarks owned by Bluetooth SIG, Inc. and any use

of such marks by Yamaha Corporation is under license.

• Sound Back is trademark of Korg Inc.

• The company names and product names in this

manual are the trademarks or registered trademarks of

their respective companies.

HD-300 Owner’s Manual

Precautions when using the USB

[TO DEVICE] terminal

This instrument features a built-in USB [TO

DEVICE] terminal. When connecting a USB device

to the USB [TO DEVICE] terminal, be sure to handle

the USB device with care. Follow the important

precautions below.

NOTE

For more information about the handling of USB devices,

refer to the owner’s manual of the USB device.

 Compatible USB devices

• USB flash drive

Other USB devices such as a USB hub, computer

keyboard or mouse cannot be used.

The instrument does not necessarily support all

commercially available USB devices. Yamaha cannot

guarantee operation of USB devices that you purchase.

Before purchasing a USB device for use with this

instrument, please visit the following web page:

https://download.yamaha.com/

Although USB devices 1.1 to 3.0 can be used on this

instrument, the amount of time for saving to or loading

from the USB device may differ depending on the type

of data or the status of the instrument.

NOTICE

The rating of the USB [TO DEVICE] terminal is a

maximum of 5V/500mA. Do not connect USB devices

having a rating above this, since this can cause damage

to the instrument itself.

 Connecting a USB device

When connecting a USB device to the USB [TO

DEVICE] terminal, make sure that the connector on the

device is appropriate and that it is connected in the

proper direction.

NOTICE

• Avoid connecting or disconnecting the USB device

during playback/recording and file management

operations (such as Delete), or when accessing the

USB device. Failure to observe this may result in

“freezing” of the operation of the instrument or

corruption of the USB device and the data.

• When connecting then disconnecting the USB device

(and vice versa), make sure to wait a few seconds

between the two operations.

• Do not use an extension cable when connecting a

USB device.

 Using USB flash drives

By connecting the instrument to a USB flash drive, you

can save data you’ve created to the connected device, as

well as read data from the connected device.

• Number of USB flash drives that can be used

Only one USB flash drive can be connected to the

[USB TO DEVICE] terminal.

 Formatting a USB flash drive

A USB flash drive cannot be formatted with this

instrument. If necessary, please format it on your

computer to FAT32 format.

NOTICE

The format operation overwrites any previously existing

data. Make sure that the drive you are formatting does

not contain important data.

 To protect your data (write-protect)

To prevent important data from being inadvertently

erased, apply the write-protect provided with each USB

flash drive. If you are saving data to the USB flash drive,

make sure to disable write-protect.

 Turning off the instrument

When turning off the instrument, make sure that the

instrument is NOT accessing the USB flash drive by file

management (such as during the Delete operation).

Failure to do so may corrupt the USB flash drive and the

data.

Precautions when using the USB

[TO HOST] terminal

When connecting the computer to the USB [TO

HOST] terminal, make sure to observe the following

points to avoid freezing the computer and corrupting

or losing the data.

NOTICE

• Use an AB type USB cable of less than 3 meters.

USB 3.0 cables cannot be used.

• Execute the following before turning the power to the

instrument on/off or plugging/unplugging the USB

cable to/from the USB [TO HOST] terminal.

- Quit any open application software on the computer.

- Make sure that data is not being transmitted from the

instrument. (Data is transmitted only by playing

notes on the keyboard.)

• While the computer is connected to the instrument,

you should wait for six seconds or more between

these operations: (1) when turning the power of the

instrument off then on again, or (2) when alternately

connecting/disconnecting the USB cable.

If the computer or the instrument freezes, restart the

application software or the computer OS, or turn the

power to the instrument off and then on again.

HD-300 Owner’s Manual

Introduction

Thank you for purchasing the Yamaha Harmony Director.

The Harmony Director is a general training instrument that facilitates harmony and rhythm training by reproducing an

accurate reference tone at a user-specified temperament and playing complex rhythms at any tempo. It also features the

ability to record performances and play time-shifted recordings to help improve your playing. The Harmony Director is a

powerful tool for anyone—from performers wanting to play in perfect tune with an ensemble of wind instruments or a

group of singers, to instructors looking to train students within a limited time span.

Please read through the contents of this manual thoroughly to fully understand and make use of the features included on

this instrument. After reading, carefully store this manual in a location where you can easily and quickly refer to it.

Included Accessories

• Owner’s Manual (this manual) × 1

• Utilization Guide/Feature Introduction × 1

•AC adaptor × 1

• Warranty information × 1

• Online Member Product Registration × 1

About this Manual

This instrument comes with the following manuals.

Owner’s Manual (This Manual)

This manual describes how to use the HD-300.

Use Guide/Feature Basics

Use Guide: This introduces features that aid a deeper level of self-directed learning.

Feature Basics: This introduces the HD-300 features suited for a range of learning situations.

These are also available from the “Manual Library” page on the following website.

Yamaha downloads

https://download.yamaha.com/

Harmony Director™ is a trademark or registered trademark of the Yamaha Corporation.

HD-300 Owner’s Manual

Contents

PRECAUTIONS..................................................................4

NOTICE ...............................................................................6

Information..........................................................................6

Introduction.........................................................................8

Included Accessories...........................................................8

About this Manual ..............................................................8

Component Names 10

Front Panel ....................................................................... 10

Rear Panel.......................................................................... 12

Setting Up 13

Power Requirements........................................................ 13

Turning the Power On/Off ............................................. 14

Adjusting the Volume and Screen Contrast................. 16

Screen Configuration and Basic Operation17

Home Screen..................................................................... 17

Producing Reference Tones for Playing

Harmony (Voice, Temperament, Hold,

Octave, Transpose) 18

Basic Operation ................................................................ 18

Temperaments.................................................................. 20

Demonstrating Tempo and Rhythm

(Metronome, Rhythm Style) 22

Basic Operation ................................................................ 22

Metronome (Simple) ....................................................... 23

Metronome (Beat • Tempo Memory) ........................... 24

Rhythm Style..................................................................... 25

Sharing Performances

(Recording/Playback) 26

Basic Operation ................................................................ 26

Recording/Playback ......................................................... 26

Playing Back Previously Recorded Files and Files Created

on a Computer (USB)...................................................... 28

Enhancing Basic Practice

(Sound Back, Training) 29

Training Your Ability to Imagine the Correct Pitch

(Sound Back)..................................................................... 29

Playing Training Examples and Accompaniments

(Training) .......................................................................... 30

Restoring Factory Settings 30

Advanced Settings (Settings) 31

Connecting External Devices 32

Connecting Amplifiers or Other Equipment

(OUTPUT [L/MONO], [R] jacks) ................................. 32

Connecting a Microphone

(MIC [INPUT] jack, MIC [GAIN] knob)..................... 32

Using a Pedal ([FOOT PEDAL] jack) ........................... 33

Connecting a USB Flash Drive

(USB [TO DEVICE] terminal) ....................................... 33

Connecting to a Computer

(USB [TO HOST] terminal) ........................................... 33

Using the “HD-300 Assistant” iPhone/iPad App

(Bluetooth) ........................................................................ 35

Listening on the HD-300 to Audio Playback from an

iPhone/iPad (Bluetooth) ................................................. 35

Appendix 36

Error Messages.................................................................. 36

Troubleshooting ............................................................... 37

About the Temperaments Used in This Instrument... 38

Specifications .................................................................... 40

Data List............................................................................. 41

HD-300 Owner’s Manual

Front Panel

[] (Standby/On) switch..............pa ge14

Switches the instrument between standby/on modes.

[MAIN VOL] slider......................... page16

Adjusts the main volume of the instrument.

[BALANCE] slider......................... page16

Adjusts the volume balance between the sounds

played with the keyboard and the rhythm style/

metronome playback.

LCD display...................................page17

Shows the instrument status, settings, and other

information.

Internal microphone.....................page16

Used for recording and the Sound Back functions.

Microphone volume LED ............. page16

Lights when the microphone input level is too high.

This is used when adjusting the sensitivity of the

microphone.

Bluetooth status LED...................page35

Indicates the Bluetooth connection status. This is

used when connecting to an iPhone or iPad.

VOICE buttons ............................. page18

Selects the Voice for use when playing the keyboard,

or when playing back the contents for training.

TEMPERAMENT buttons..... pages 18, 21

These set the temperament (equal/pure/individual)

and lock/unlock the root key auto detection.

TRANSPOSE buttons .................. page19

These configure the keyboard transpose settings and

are used when playing a music score for a transposing

instrument as notated.

[OCTAVE] slider........................... page19

Adjusts the keyboard octave.

[HOLD] button .............................. page19

Used to keep the played notes sounding even after the

keys are released.

[SOUND BACK] button................ page29

Switches the Sound Back function on and off.

RECORDING buttons................... page26

Used for recording and playback.

Component Names

HD-300 Owner’s Manual

[RHYTHM STYLE] button.....pages 22, 25

Sets the rhythm playback to the Rhythm Style mode.

[BEAT] button.................pages 22, 23, 24

Sets the rhythm playback to the Metronome mode.

Dial, [-]/[+] buttons .......................page17

Used to change settings and select files.

[START/STOP] button.... pages 22, 28, 30

Starts/stops the rhythm style, metronome, training

content playback, or playback of a file on a USB flash

drive.

[TEMPO/TAP] button....................page22

Adjusts the playback tempo.

BEAT • TEMPO MEMORY buttons

...............................................pages 22, 24

Used to enter, store, and load special metronome

beats.

NOTE

The CURSOR [ ][ ] buttons are also used to move the

cursor for other functions.

[METRONOME VOL] slider

... pages 16, 23

Adjusts the volume for each metronome note type.

[TRAINING] button....................... page30

This sets the instrument to the training content (JBS

content) playback mode.

[USB] button................................. page28

Sets the instrument to the USB file playback mode.

[EXIT] button .................. pages 28, 30, 31

Moves up one hierarchy level on the screens, such as

training, USB file playback, and advanced settings, or

exits from it.

[SETTING] button......................... page31

Enters the advanced settings screen.

Component Names

HD-300 Owner’s Manual

Rear Panel

[FOOT PEDAL] jack..............pages 31, 33

For connecting the Foot Controller FC7 (sold

separately). You can control the function with your

foot, by assigning either the main volume, hold, start/

stop or record/stop function to the FC7.

OUTPUT [L/MONO]/[R] jack.........page32

This is a standard phone jack that outputs audio

signals. Connect these to an external amplifier or

speaker for outputting the audio at loud levels.

To use with and mono amplifier, only connect to the

[L/MONO] jack.

MIC [INPUT] jack, MIC [GAIN] knob

...............................................pages 16, 32

For connecting a commercially available microphone

(with a stereo mini-phone jack and plug-in power

compatibility). When an external microphone is

connected, the internal microphone will be disabled.

Turn the [GAIN] knob to adjust the sensitivity of the

internal microphone and the external microphone.

USB [TO HOST] terminal....... pages 7, 33

For connecting to a computer using a commercially

available USB cable. When connected, you can send

and receive MIDI and audio data.

USB [TO DEVICE] terminal ... pages 7, 33

For connecting a USB flash drive required to use the

recording and file playback functions.

DC IN jack ..................................... page13

For connecting the power adaptor that comes with

this instrument, or one sold separately.

Cord hook..................................... page13

Used to prevent damage to the cord of the AC

adaptor.

FC7

Keyboard amplifier or

monitor speaker

Computer

Microphone USB flash drive

Power outlet

AC adaptor

HD-300 Owner’s Manual

Power Requirements

This instrument can be operated either from an AC adaptor or batteries. Yamaha recommends use of an AC adaptor

whenever possible, since an AC adaptor is more environmentally friendly than batteries and does not deplete resources.

NOTICE

You should use an AC adaptor when using a USB flash memory drive. Using battery power could cause the power to go out

during operation, resulting in data loss.

Connect the AC adaptor in the order shown in the illustration.

WARNING

• Only use the specified AC adaptor (page 40). Using the wrong AC adaptor can result in

damage to the instrument, overheating, or fire accidents. Note that an accident caused

by incorrect usage may void the warranty even if the instrument is still within the

warranty period.

• When using an AC adaptor with a removable plug, make sure to keep the plug attached

to the AC adaptor during use or storage. Inserting the plug alone into the AC outlet can

cause electric shock or fire.

•If the plug is accidentally removed from the AC adaptor, insert the plug all the way in

until you hear a click, taking care to avoid touching any internal metal parts. To avoid electric shock, short circuit, or damage

to the instrument, also be careful that there is no dust between the AC adaptor and plug.

CAUTION

When setting up the product, make sure that the power outlet you are using is easily accessible. If some trouble or malfunction

occurs, immediately turn the power off and disconnect the plug from the outlet.

NOTICE

Hook the cable of the AC adaptor on the cord hook to prevent damage to the cable.

NOTE

To remove the AC adaptor, turn the power off first, and then follow the above instructions in reverse order.

Setting Up

Using an AC Adaptor

AC adaptor

DC IN jack (page 12)

AC outlet

Plug

Slide in the

plug as

indicated

Setting Up

HD-300 Owner’s Manual

This instrument accepts AA alkaline batteries and rechargeable Ni-MH (Nickel-Metal Hydride) batteries.

1. Make sure that the power of the instrument is off.

2. Turn the instrument over and place it on a soft cloth.

Open the battery compartment cover located on the

instrument’s bottom panel.

3. Insert six new batteries. Make sure that they are

orientated correctly according to the illustration.

4. Close the battery compartment with the cover.

NOTICE

• Do not connect or disconnect the DC plug of the AC adaptor while the

power is on, even if the batteries are installed. Doing so, the power will

suddenly turned off and this result in the loss of data being recorded

or transferred at the time.

• When battery power becomes low, a message saying “Low Battery”

will appear on the screen. When this happens, either replace or

recharge all batteries. If you continue to use the instrument in this

condition, it may not work properly, or the power will suddenly and

automatically turn off because of insufficient power.

NOTE

• Use only the specified charger device for charging rechargeable batteries.

This instrument cannot be used to recharge batteries.

• Power will be automatically drawn from the AC adaptor when an AC

adaptor is connected even if batteries are installed in the instrument.

Turning the Power On/Off

1. Move the [MAIN VOL] slider to the left to

reduce the volume to the minimum setting.

2. If necessary, connect any external devices

(amplifiers for digital instrument, etc.) to

the instrument.

For details on how to connect these devices, refer

to “Connecting External Devices” (page 32).

3. Press the [] (Standby/On) switch to turn

the power on.

The screen on the instrument will appear.

4. Turn the power on to any external devices,

and then adjust the volume and other

settings on the external device.

5. Adjust the volume on the instrument.

5-1. Center the [BALANCE] slider.

5-2. Gradually shift the [MAIN VOL] slider to the right to raise the volume while playing the

keyboard.

NOTICE

Do not attempt to use the instrument (press any keys or buttons, or step on pedals, etc.) after turning on the power until the

instrument has completely started up (the Home screen appears). Doing so may cause the instrument to malfunction.

Using Batteries

Turning the Power On

Bottom of the instrument

Battery compartment cover

Setting Up

HD-300 Owner’s Manual

1. When an external device is connected, first turn the volume down on the external device and then

turn off the power of the external device.

2. Move the [MAIN VOL] slider to the minimum setting.

3. Press and hold the [] (Standby/On) switch for one second, and then release it.

A message will appear on the display, and the power will be turned off after a few seconds.

CAUTION

Even when the power is off, a small amount of electricity is still flowing through the instrument. Make sure to unplug the AC

adaptor from the power outlet when you intend not to use the instrument for an extended period of time or during electrical

storms. When using batteries, remove the batteries from the instrument.

To prevent unnecessary power consumption, this instrument features an Auto Power Off function that automatically

turns the power off if the instrument is not operated for a specific period of time. The amount of time that elapses before

the power is automatically turned off depends on the type of power being used. This is set to 30 minutes for battery

power, and two hours when using an AC adaptor.

The Auto Power Off function can be enabled/disabled on the Settings screen (page 31).

 Disabling Auto Power Off

• When the power is off

Turn the power on while holding down the lowest key on the

keyboard.

•When the power is on

Press the [SETTING] button to call up the Settings screen, and then

set “AutoPowerOff ” to “Disable.”

 Enabling Auto Power Off

Press the [SETTING] button to call up the Settings screen, and then set

“AutoPowerOff” to “Enable.”

NOTICE

When you intend not to operate this instrument for a specific period of time

while connecting to an external device such as an amplifier, speaker, or

computer, make sure to follow the instructions in the Owner’s Manual to turn off the power to the instrument and the connected

external devices in order to protect the devices from damage. If you do not want the power to turn off automatically when a

device is connected, disable the Auto Power Off function.

NOTE

To move the cursor on the Settings screen, use the BEAT • TEMPO MEMORY CURSOR [ ][ ] buttons. To change values, use the [-]/

[+] buttons.

Turning the Power Off

Auto Power Off Function

Setting Up

HD-300 Owner’s Manual

Adjusting the Volume and Screen Contrast

To adjust the volume of the entire sound of this instrument, use the

[MAIN VOL] slider while playing the keyboard.

In addition, the following volume sliders are also available.

•

[BALANCE] slider: Adjusts the volume balance between the

keyboard and rhythm playback.

Turn this left to increase the volume of the keyboard.

Turn this right to increase the volume of the rhythm playback

(metronome, Rhythm Style, etc.).

•

[METRONOME VOL] slider: Adjusts the volume of each

metronome note type individually.

CAUTION

Do not use the instrument at a high volume level for a long period of time.

Doing so can cause hearing loss.

Use the MIC [GAIN] knob on the rear panel to adjust the

microphone sensitivity while speaking or singing into the microphone.

Configure this so the microphone volume (CLIP) LED at the top left of

the panel does not light up even when the sound you want to record is

at maximum volume.

NOTE

• You can also check the volume of input sounds on the input level meter on

the bottom left of the LCD display. When using this to adjust settings, adjust

the sensitivity until “Clip!” no longer appears on the screen.

• If the microphone volume indicator (CLIP) LED lights even when the MIC

[GAIN] knob is turned down, adjust by increasing the distance between this

unit and the sound source.

• Sound input from the microphone is used only for recording and the Sound

Back function. It will not be output from the line output or speaker.

Press the [SETTING] button to call up the Settings screen, and then

change the “LCD Contrast” value.

NOTE

To move the cursor on the Settings screen, use the BEAT • TEMPO MEMORY

CURSOR [ ][ ] buttons. To change values, use the [-]/[+] buttons.

Adjusting the Volume

Adjusting the Sensitivity of the Microphone

Adjusting the Screen Contrast

HD-300 Owner’s Manual

Turn the power on to display the Home screen.

Home Screen

Items – relate to tuning, to recording, and and relate to rhythm playback.

Voice

Shows the voice option currently selected. (Page 18)

Standard pitch

Shows the standard pitch. (Pages 20, 31)

Transpose

Shows the transpose settings. (Page 19)

Temperament, root key, chord

Shows the current temperament settings

(temperament and root key), and the chord detected.

(Pages 18 – 21)

Recording, microphone input

Shows the recording status, and the microphone input

level. (Pages 16, 26, 29)

Tempo, reference note

Shows the tempo, and the tempo reference note.

(Page 22)

Beat, memory number

Shows the beat, or the beat • tempo memory (irregular

meter). (Pages 22 – 25)

• The location of the cursor is highlighted, and the cursor can be

controlled with the [-]/[+] buttons and the dial. In the image above,

the cursor is on “M1.”

•Press the panel buttons (CURSOR [ ][ ] buttons, etc.) to move

the cursor and change items/settings in the screen display.

• Press the [INDIVIDUAL VOL/PITCH] button (page 21),

[TRAINING] button (page 30), [USB] button (page 28), or the

[SETTING] button (page 31) to call up their respective screens.

Each screen is described in greater detail in the above pages.

NOTE

When the [-] and [+] buttons are pressed simultaneously, the value currently

focused will reset to the default value.

Screen Configuration and Basic Operation

Screen Elements

Basic Operation

HD-300 Owner’s Manual

Basic Operation

The HD-300 can be used to produce reference tones to play along with as a way of developing your sense for playing your

instrument in the correct pitch.

This chapter provides detailed instructions for the necessary operations shown below:

You can select the sounds produced when playing the keyboard.

Press one of the VOICE buttons to select a category, and then select the

desired Voice within the category by using the dial, or the [-]/[+]

buttons.

Available Voices are divided into two types: one using FM tone

generation and the other using the PCM tone generation. The VOICE

buttons correspond to the following tone generation systems.

•

[WOOD]/[BRASS]/[ORGAN] buttons: FM tone generation

•

[PIANO/OTHERS] button: PCM tone generation

FM tone generation Voices are compatible with the Equal, Pure, and

Individual temperaments in the temperament setting function, and so are suitable for producing reference tones for

harmony. PCM tone generation Voices can only be used Equal temperament, but are useful since there are a variety of

available sounds.

For details on the Voices of each category, refer to page 41.

You can configure advanced settings, such as the root key and temperament (Equal/Pure/Individual temperament) of the

song.

•

Setting the root key: See the page 20.

•

Setting the temperament: Use the TEMPERAMENT [EQUAL]/[PURE]/[INDIVIDUAL VOL/PITCH] buttons to

select a temperament mode out of the three available. The lamp of the selected temperament mode will light. The

corresponding screen displays are listed below.

Producing Reference Tones for Playing Harmony (Voice,

Temperament, Hold, Octave, Transpose)

Selecting a Voice

Voice settings for tuning

While there is no specific rule-of-thumb on which reference sound to use, you should select a Voice that is easily

recognizable for both the conductor and performers. (Generally, organ or string-type sounds are ideal for

distinguishing slight differences in pitch, due to their rich harmonic tone.)

Setting the Temperament

Preparation Producing the reference tone(s) Playing the instrument(s)

• Selecting a Voice

• Setting the temperament

• Setting hold on/off

• Selecting an octave

• Setting transpose

Playing the keyboard

Playing wind instrument(s) etc.

to match the reference tone

Producing Reference Tones for Playing Harmony (Voice, Temperament, Hold, Octave, Transpose)

HD-300 Owner’s Manual

NOTE

• When the [PIANO/OTHERS] button is pressed, Equal temperament is automatically selected.

• When you select Pure or Individual temperament mode, the Voice type using the FM tone generator is automatically selected.

• For details on setting the Individual temperament (individual volume/pitch), see page 21.

Turn the hold function on to continue playing a note even after your

finger leaves the keyboard.

Press the

[HOLD] button to have the lamp light up and turn the hold

function on. When a note is continually played with the hold function,

pressing a different note on the keyboard will stop the previous sound

and start to continually play the sound for the newly pressed note.

To stop the sound being produced, press the [HOLD] button again and

turn the hold function off.

Use the

[OCTAVE] slider to select the octave of notes played with

the keyboard.

The relationship between the slider position and octave is as follows.

This function is used to match the keyboard sound to a transposing

instrument. With this function, you can play the sounds at the same

pitch as the transposing instrument by playing the keyboard, while

using the musical score written for the transposing instrument,

without having to transpose it to the score for the keyboard.

Press the [C]/[B

]/[E

]/[F] buttons to set the transpose value directly

without moving the cursor.

Button [EQUAL] [PURE] [INDIVIDUAL

VOL/PITCH]

Display on screen

Equal Pure User

Temperament mode

Equal temperament Pure temperament Individual (custom)

temperament

Setting Hold On/Off

Selecting an Octave

Slider position LOW1 LOW2 MID HI

Octave

C-1 – C4 C0 – C5 C1 – C6 C2 – C7

Setting Transpose

Button [C] [B

] [E

] [F]

Transpose

value

0 -2 semitones +3 semitones +5 semitones

Producing Reference Tones for Playing Harmony (Voice, Temperament, Hold, Octave, Transpose)

HD-300 Owner’s Manual

You can also press the [TRANSPOSE] button and move the cursor to the transpose area to adjust the transpose value.

Adjust the transpose value using the dial or the [-]/[+] buttons. The transpose value range is -2 – +12 semitones. Press

both [-]/[+] buttons simultaneously to return the transpose value to 0.

Temperaments

Users can configure advanced settings, such as the root key and temperament (Equal/Pure/Individual temperament)

settings, using this function.

The root key is primarily used to determine the keynote for the “Pure” and “Individual” settings.

To set the root key, play a chord on the keyboard.

The instrument will recognize the chord pressed and change the root key accordingly. For major chords this will be set to

major (displayed in upper case letter), and for minor chords this will be set to minor (displayed in lower case letter). The

recognized chord and the root key will appear on the screen.

NOTE

If the chord cannot be determined, the root key will not change.

Chord detection and root key changes continue with each key pressed

on the keyboard. To lock (fix) the current root key, press and hold the

[PURE] button.

When a root key is locked, a icon will appear to the right of the

chord name on the screen. Additionally, if a pure temperament is

selected, the [PURE] button lamp will light up in green.

NOTE

Chord detection will stop when the root key is locked.

Changing the standard pitch

To change the standard pitch from 442Hz, call up the Settings screen by pressing the [SETTING] button, and change

the “Standard Pitch” value.

NOTE

To move the cursor on the Settings screen, use the BEAT • TEMPO MEMORY CURSOR [ ][ ] buttons. To change values, use the

dial or [-][+] buttons. To exit from the menu, press the [EXIT] button.

Setting the Root Key

Name of the recognized chord

Name of the current root key. Upper case letter means major,

and lower case letter means minor.

A página está carregando ...

Yamaha HD-300 Manual do proprietário

Marca: Yamaha

Modelo: HD-300

Tipo: Manual do proprietário

baixar PDF

relatório

em outros idiomas

italiano: Yamaha HD-300 Manuale del proprietario
English: Yamaha HD-300 Owner's manual

Yamaha HD-300 Manual do proprietário

Yamaha HD-300 Manual do proprietário

em outros idiomas

Artigos relacionados

Outros documentos