Whirlpool AKR 966 AL Manual do proprietário

Marca: Whirlpool

Modelo: AKR 966 AL

Categoria: Exaustores

Tipo: Manual do proprietário

5019 318

33157



AKR 631-666-812-966

AKR 943-948-952-995-996

INSTALLATIONSBESCHREIBUNG

Mindestabstand über der Kochfläche: 50 cm (Elektrokochplatten), 70 cm (Gas-, Öl-

oder Kohlekochplatten). Schreiben die Installationsanweisungen des Gaskochfelds

einen größeren Abstand vor, ist dieser natürlich zu beachten. Folgen Sie bei der

Installation der Nummerierung (1

.....). Schließen Sie das Gerät erst nach

seiner kompletten Installation an das Stromnetz an. Achtung! Das Auslassrohr und die

Befestigungsmanschetten sind nicht im Lieferumfang inbegriffen und müssen

gesondert erworben werden.

INSTALLATION DATA SHEET

Minimum height above cooker: 50 cm (electric cookers), 65 cm (gas, gas oil or coal

cookers). If the installation instructions for a gas cooker specify a greater distance,

then this distance must be observed. To install, follow steps (1

.....). Do not

connect the hood to the electrical power supply until installation is completed.

Warning! The exhaust pipe and clamps are not supplied and must be bought

separately.

FICHE D'INSTALLATION

Distance minimale par rapport à la cuisinière : 50 cm (cuisinière électrique), 70 cm

(cuisinière à gaz, mazout ou charbon). Si les instructions d'installation du dispositif de

cuisson à gaz indiquent une distance supérieure, il est nécessaire de la respecter. Pour

le montage, suivez la numérotation (1

.....). Ne branchez pas l'appareil tant

que l'installation n'est pas terminée. Attention ! Le conduit d'évacuation et les colliers

de fixation ne sont pas fournis et doivent être achetés à part.

INSTALLATIEKAART

Minimumafstand tot het kooktoestel: 50 cm (elektrische kooktoestellen), 70 cm

(kooktoestellen op gas, olie of kolen). Als de installatie-instructies van het kooktoestel

op gas een grotere afstand aangeven, moet hiermee rekening gehouden worden. Volg

voor de montage de nummering (1

.....). Geef het apparaat geen stroom totdat

de installatie geheel voltooid is. Let op! De afvoerbuis en de klembanden worden niet

bijgeleverd en moeten apart worden aangeschaft.

31833157.fm Page 1 Friday, April 1, 2005 5:04 PM

5019 318

33157

AKR 631-666-812-966

AKR 943-948-952-995-996



FICHA DE INSTALACIÓN

Distancia mínima desde los quemadores: 50 cm (fuegos eléctricos), 70 cm (fuegos de

gas, gasóleo o carbón). Si en las instrucciones de instalación de la placa de cocina a gas

se especifica una distancia mayor respecto a la indicada, es necesario tenerlo en

cuenta. Para el montaje, siga la numeración (1

...). No conecte el aparato a la

corriente eléctrica hasta que la instalación esté completamente finalizada. ¡Atención!

El tubo de descarga y las abrazaderas de fijación no están incluidas y se compran

aparte.

FICHA DE INSTALAÇÃO

Distância mínima dos fogões: 50 cm (fogões eléctricos), 70 cm (fogões a gás, óleo ou

carbono. Respeite as instruções de instalação do dispositivo de cozedura a gás se estas

especificarem uma distância superior à indicada. Para montar siga a numeração

.....). Não ligue o aparelho à corrente eléctrica enquanto a instalação não

estiver concluída. Atenção! O tubo de descarga e as braçadeiras de fixação não são

fornecidas e devem ser compradas à parte.

SCHEDA INSTALLAZIONE

Distanza minima dai fuochi: 50 cm (fuochi elettrici), 70 cm (fuochi a gas, gasolio o

carbone). Se le istruzioni di installazione del dispositivo di cottura a gas specificano una

distanza maggiore rispetto a quella specificata, bisogna tenerne conto. Per il

montaggio seguire la numerazione (1

.....). Non dare corrente all’apparecchio

finché l’installazione non è totalmente completata. Attenzione! Il tubo di scarico e le

fascette di fissaggio non sono fornite e vanno acquistate a parte.

ùüùü+ùùùþ

ü$12.)12.1.)2"0120"FP02!"0120"FP0120".0! #

02!0. #0! # ü  /0"0.212.1"2"012.".0! #1#12 *

0.*20!.)12.1101$1000 #$0 !12003.!)1202"1$02"

/0"+.22  21.  #1202.!1





2! 3 / 2020

002!)!0*.21#10#!2  !&12"0.212.1"! 1 $

1&."..&".2. !.120!&1"/0/.202..!0.. 2 *

$&!12

31833157.fm Page 2 Friday, April 1, 2005 5:04 PM

5019 318

33157



AKR 631-666-812-966

AKR 943-948-952-995-996

31833157.fm Page 3 Friday, April 1, 2005 5:04 PM

5019 318

33157

AKR 631-666-812-966

AKR 943-948-952-995-996



Remove the perimeter extraction panel (if relevant) and the grease filter/s.

Pre-assemble the steam deflector on the motor assembly (if relevant): (a.) fit the steam deflector to the rails of the motor

assembly (remove the two travel stop screws from the steam deflector if necessary), (b.) connect up the control panel and

the lamps, (c.) fix in place with the 14 screws (max).

1. Mark a line on the wall right up to the ceiling, corresponding to the centre-line of the hood.

2. Apply the drilling template to the wall: Align the vertical centre-line on the drilling template with the centre-line drawn

on the wall. The template's bottom edge represents the bottom edge of the hood.

3. Place the mounting bracket over the drilling template so that it matches the outlined rectangle. Mark and drill the two

outside holes. Remove the drilling template. Insert two wall plugs in the holes and fix the hood mounting bracket in place

with two 5 x 45 mm screws.

4. Hang the hood on the mounting bracket. Adjust gap (5.) and the horizontal alignment (6.) of the hood.

5. Remove the hood from the bracket. Drill the holes (9. - Ø 8 mm - see step 7.). Insert two wall plugs (10.).

6. Apply the flue mounting bracket G to the wall against the ceiling. (Align the small slot in the bracket with the centre-line

drawn on the wall. See step 1. Fix the bracket in place with two wall plugs (Ø 8 mm) and 2 screws 12).

7. Hang the hood on the bottom mounting bracket. (14.) Fix the hood to the wall with two 5 x 45 mm screws

(ABSOLUTELY NECESSARY). Plug the two holes if they are visible from the outside.

8. Connect an exhaust pipe to the to the collar B, the fumes must be ducted to the outside (extractor version) or towards

the deflector (filter version). Fix the deflector F to the flue support bracket G with 4 screws (2 screws only for 120 cm

wide model). If the collar (bayonet coupling) is not already fitted, insert it on the deflector F and secure it with 1 screw.

9. Make all necessary electrical connections.

10. Apply the flues and fix them with 2 screws (17a) to the flue support G (17b).

11. Slide the bottom section of the flue all the way over the extraction unit until it engages the seat above the hood.

12. (120 cm wide model only) fix the bottom section of the flue to the hood with 2 screws.

Re-fit the grease filter/s and, if a perimeter extraction panel is fitted, check for correct operation.

Important! Only for model AKR 996: proceed with hob selection and manual calibration of the sensors. For this purpose,

read the paragraph on the next page “Important - upon initial installation”.

1. Control panel.

2. Grease filter.

3. Halogen bulbs.

4. Steam deflector.

5. Telescopic flue.

6. Perimeter extraction

panel (if fitted) and

release handle (f3).

7. Sensors (only present on

some models).

INSTALLATION - ASSEMBLY INSTRUCTIONS

IF NL E PGBD GR

31833157.fm Page 8 Friday, April 1, 2005 5:04 PM

5019 318

33157



AKR 631-666-812-966

AKR 943-948-952-995-996

Analogue control panel

Light : move the switch to the right or press the button to switch on.

Extraction speed : Move the switch to the right or press the next button to increase extraction speed

(or open the electric shutter ).

Digital control panel with sensors

The hood is fitted with a series of sensors which enable it to operate in 2 modes:

Automatic

mode

and

Manual mode

Automatic mode:

the hood switches on automatically, depending on the ambient temperature (and heat) and variations in

this detected by the hood's sensors. See description of Button 3 function.

Manual mode:

the hood is switched on by the user.

Description of Buttons

1. OFF/Stand by button:

When the hood is OFF, all the controls are disabled (all LEDs are off).

When on stand-by, the hood is ready to operate in “

Manual mode

”, LED C lights up.

2. Light ON/OFF button: always works, even when the hood is OFF.

3. ON/OFF button “

Automatic mode

”: press to activate this mode (LED C and E on) the hood switches on automatically,

selecting a suitable extraction speed in accordance with the ambient temperature (and heat) and any variations in this

detected by the hood's sensors. Press again to revert to

“Manual mode”

: LED E switches off, LED C remains on (stand

by). The hood will continue to run for a few minutes after you have finished cooking but can be turned off by pressing

buttons 1 or 3. The automatic function (LED on) stops a few minutes after the motor has been switched off. The

automatic function must be switched on every time you start cooking.

4. ON/OFF button for controlling intensive extraction speed in “

Manual mode

” (LED D switches on): when selected, it

operates for 5 minutes, after which time the hood automatically reverts to the previously selected extraction speed.

5. Buttons for controlling extraction speed 1 - 2 - 3 in “

Manual mode

”.

Description of LEDs

Carbon filter

saturation led indicator

: this led lights up to indicate that the carbon filter needs to be cleaned or replaced.

Important: this indicator must be activated in order for the hood to work:

to activate it, press buttons 4 and 5 at the

same time - LED B lights up first, followed by LED A to indicate that the led indicator is working.

Grease filter saturation led indicator: this led lights up to indicate that the grease filter needs to be cleaned.

“Stand by” led indicator.

Intensive speed led indicator.

“Automatic mode” led indicator.

Extraction speed 1 led indicator.

Extraction speed 2 led indicator.

Extraction speed 3 led indicator.

Reset filters indicator:

After cleaning or replacing the filters, with the hood on

Stand by

press Button 1 for more than 3 seconds.

Safety function: this function is activated ONLY with the hood on stand-by, in the event of any SUDDEN, VIOLENT

increase in the temperature detected by the sensors, upon which the hood switches to “

Automatic mode

” and, if necessary,

selects a suitable extraction speed.

Important - upon initial installation:

Selecting the hob type: to ensure accurate “reading” by the sensors, the latter must be calibrated to suit the type of hob

as follows: with the hood OFF, press buttons 3 and 4 at the same time until either LED F for gas hobs, LED G for induction

hobs or LED H for electric hobs lights up.

Automatic and manual sensor calibration: the hood automatically “calibrates” sensor operation, but under certain

circumstances (e.g.: in the event of a prolonged power failure or upon initial installation) calibration can be carried out

manually, with the hood OFF, by pressing buttons 5 and 6 at the same time for more than 3 seconds, otherwise you can wait

until the hood carries out calibration automatically.

PRODUCT SHEET

IF NL E PGBD GR

31833157.fm Page 9 Friday, April 1, 2005 5:04 PM

5019 318

33157

AKR 631-666-812-966

AKR 943-948-952-995-996



Maintenance

ALWAYS disconnect the hood from the mains before

performing maintenance.

Wash the grease filter and the carbon filter in a

dishwasher once a month, at the highest possible

temperature, using normal dishwasher detergent. It is

recommended to wash the filters on the their own.

After washing, reactivate the carbon filter by drying it in

the oven at 100 °C for 10 minutes. Fit a new carbon filter

every 3 years.

Remove the grease filters - Fig. 1: push the spring release

handle backwards (f1) then remove the filter downwards

(f2).

Clean the perimeter extraction panel (if provided) as

often as the grease filter, using a cloth and a mild liquid

detergent.

Never use abrasive substances.

Clean the sensor plate regularly.

Replacing bulbs

1. Use a small screwdriver or any other suitable tool to

prise off (m-Fig. 1) the lamp cover (p-Fig.1).

2. Remove the burnt-out bulb.

Use max 20 W halogen bulbs only, taking care not to

touch them with your hands.

3. Close the lighting unit (snap-on).

Fitting the carbon filter:

1. Remove the grease filter (f1/f2 - Fig. 1).

2. Remove the filter holder by turning the knobs

(g - Fig. 2) through.

3. Fit the carbon filter (i - Fig. 2) in the filter holder

(h - Fig.2).

Reverse the above procedure to re-fit the filter holder and

grease filter.

Fig. 2

* Only present on some models

Fig. 1

IF NL E PGBD GR

31833157.fm Page 10 Friday, April 1, 2005 5:04 PM

Whirlpool AKR 966 AL Manual do proprietário

Marca: Whirlpool

Modelo: AKR 966 AL

Categoria: Exaustores

Tipo: Manual do proprietário

baixar PDF

relatório

em outros idiomas

français: Whirlpool AKR 966 AL Le manuel du propriétaire
italiano: Whirlpool AKR 966 AL Manuale del proprietario
English: Whirlpool AKR 966 AL Owner's manual

Whirlpool AKR 966 AL Manual do proprietário

Whirlpool AKR 966 AL Manual do proprietário

em outros idiomas

Artigos relacionados